Front Seat Assembly (For Manual Seat) Disassembly

Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.

HINT:

Tape the screwdriver tip before use.

Remove the 2 screws and vertical adjusting handle LH.

Remove the snap ring and vertical seat adjuster knob.

Lift the reclining adjuster release handle LH.

Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

HINT:

Tape the screwdriver tip before use.

w/ Seatback Board:
Disconnect the 2 rubber bands from the 2 hooks.

w/o Seatback Board:
Disconnect the rubber band from the 2 hooks.

for 4 Way Seat Type:

1. Remove the 2 screws.
   

2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
   

for 8 Way Seat Type:

1. Remove the 3 screws.
   

2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
   

w/ Lumbar Support:
Disconnect the lumbar switch connector.

Remove the 2 screws and lumbar switch.

Disconnect the connectors and detach the clamps.

Remove the nut and front seat inner belt assembly.

Remove the front seat belt anchor plate.

Remove the screw.

Detach the claw and clip, and then remove the front inner seat cushion shield LH.

Using a clip remover, remove the 2 clips.

w/ Lumbar Support:
Detach the wire harness clamp.

w/ Occupant Detection Sensor:
Detach the 2 clamps and remove connector holder.

Bend the 2 seat frame claws upward.

Detach the hooks and remove the seat cushion cover with pad.

Remove the hog rings and front separate type seat cushion cover from the front separate type seat cushion pad.

Remove the 2 screws.

Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.

Detach the 4 claws and remove the 2 front seat headrest supports.

w/ Seatback Board:

1. Remove the 3 hog rings and detach the 9 hooks.
   





2. w/ Front Seat Side Airbag:
   Remove the nut and seatback cover bracket from the seat frame.
   

w/o Seatback Board:

1. Remove the 3 hog rings.
   





2. Open the 2 fasteners, and then open the front separate type seatback cover.
   





3. w/ Front Seat Side Airbag:
   Remove the nut and seatback cover bracket from the seat frame.
   





4. Detach the 4 claws and remove the 2 front seat headrest supports.
   

Remove the seatback cover with pad from the seatback frame.

w/ Front Seat Side Airbag:
Disconnect the seatback cover bracket from the front separate type seatback pad.

Remove the hog rings.

Detach the fastening tape and remove the front separate type seatback cover from the front separate type seatback pad.

w/ Front Seat Side Airbag:
Detach the wire harness clamp.

Remove the screw.

Detach the claw and remove the inside reclining adjuster cover LH.

w/ Lumbar Support:
Detach the wire harness clamp.

Remove the screw.

Detach the claw and remove the inside reclining adjuster cover RH.

Remove the screw and outside reclining adjuster cover LH.

Remove the screw and outside reclining adjuster cover RH.

Remove the 4 springs.

w/ Active Headrest:
Remove the cable clamp and disconnect the active headrest cable from the seatback spring.

Detach the 4 hooks and remove the seatback spring.

Disconnect the lumbar support adjuster connector.

Remove the 2 screws and lumbar support adjuster assembly LH.

Detach the 3 claws and remove the bush from the seat frame.

Remove the 6 nuts, and then remove the lower active headrest unit together with the upper active headrest unit.

Remove the nut.

Detach the cable clamp and remove the upper active headrest unit from the lower active headrest unit.

Detach the claw and remove the front lower seat cushion shield LH.

Detach the claw and remove the front lower seat cushion shield RH.

Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.

Disconnect the connector.

Remove the seat slide position sensor protector from the seat position sensor.

Remove the front seat assembly LH (Click here).

Detach the wire harness clamps.

Detach the claw and remove the front seat wire LH.

for 4 Way Seat Type:

1. Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.
   





2. Using a T40 "TORX" socket wrench , remove the 4 "TORX" bolts and seat frame with adjuster.
   





3. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and reinforcement.
   

for 8 Way Seat Type:

1. Detach the spring.
   

2. Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.
   

3. Using a T40 "TORX" socket, remove the "TORX" bolt and spring.
   





4. Using a T40 "TORX" socket, remove the 4 bolts and seat frame with adjuster.
   





5. Using a T40 "TORX" socket wench, remove the 2 "TORX" bolts and reinforcement.
   

Using a screwdriver, detach the spring and remove the front inner seat track assembly LH from the seat track adjusting handle as shown in the illustration.

Using a screwdriver, detach the spring and remove the front outer seat track assembly LH from the seat track adjusting handle as shown in the illustration.