Front Seat Side Airbag Assembly (For Manual Seat) -- Installation |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedures for LHD and RHD vehicles.
- The procedures listed below are for LHD vehicles.
| 1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH |
- CAUTION:
- Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.
Install the front seat airbag assembly with 2 nuts.
- Torque:
- 5.5 N*m{56 kgf*cm, 49 in.*lbf}
 |
Attach the 2 clamps to connect the wire harness.
Attach the 5 clamps to connect the wire harness.
 |
| 2. INSTALL SEATBACK COVER WITH PAD |
Set the seatback cover with pad in place.
w/ Seatback Board:
w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.- Torque:
- 5.0 N*m{51 kgf*cm, 44 in.*lbf}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Attach the 9 hooks.
Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
w/o Seatback Board:
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.- Torque:
- 5.0 N*m{51 kgf*cm, 44 in.*lbf}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Close the 2 fasteners.
Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
| 3. INSTALL FRONT SEAT HEADREST SUPPORT |
 |
Attach the 4 claws to install the 2 front seat headrest supports.
| 4. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board) |
 |
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
| 5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH |
 |
Attach the claw and clip to install the front inner seat cushion shield LH.
Install the screw.
| 6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
Install the front seat belt anchor plate.
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
 |
Connect the connectors and attach the clamps.
| 7. INSTALL FRONT SEAT CUSHION SHIELD LH |
w/ Lumbar Support:
Connect the lumbar switch connector.
for 4 Way Seat Type:
Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 2 screws.
for 8 Way Seat Type:
Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 3 screws.
w/ Seatback Board:
Connect the 2 rubber bands to the 2 hooks.
 |
w/o Seatback Board:
Connect the rubber band to the 2 hooks.
 |
| 8. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
 |
Attach the claw to install the reclining adjuster release handle LH.
| 9. INSTALL VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type) |
 |
Install the snap ring to the vertical seat adjuster knob.
Install the vertical seat adjuster knob.
| 10. INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type) |
 |
Install the vertical adjusting handle with the 2 screws.
| 11. INSTALL VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type) |
 |
Attach the 2 claws to install the vertical adjuster cover LH.
| 12. INSTALL FRONT SEAT ASSEMBLY LH |
Install the front seat assembly LH (Click here).