Dtc B1630/23 Rear Airbag Sensor Rh Circuit Malfunction

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Supplemental Restraint Systems. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FOR DTC

CHECK REAR AIRBAG SENSOR RH

CHECK SIDE AIRBAG SENSOR LH

DTC B1630/23 Rear Airbag Sensor RH Circuit Malfunction

DTC B1695/16 Door Side Airbag Sensor LH Malfunction


DESCRIPTION

HINT:
"Door side airbag sensor LH" refer to the side airbag sensor LH.
  1. The side airbag sensor LH or rear airbag sensor RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
    If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
    DTC B1630/23 or B1695/16 is stored when a malfunction is detected in the side airbag sensor LH or rear airbag sensor RH circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1630/23
When one of the following conditions is met:
  1. A rear airbag sensor RH malfunction.
  2. A center airbag sensor malfunction.
  1. Rear airbag sensor RH
  2. Center airbag sensor assembly
B1695/16
When one of the following conditions is met:
  1. A side airbag sensor LH malfunction.
  2. A center airbag sensor malfunction.
  1. Side airbag sensor LH
  2. Center airbag sensor assembly

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Supplemental Restraint Systems.Airbag System. Dtc B1630/23 Rear Airbag Sensor Rh Circuit Malfunction


Land Cruiser. Urj200, 202 Grj200 Vdj200.Supplemental Restraint Systems.Airbag System. Dtc B1630/23 Rear Airbag Sensor Rh Circuit Malfunction


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
1.CHECK FOR DTC

  1. Turn the ignition switch to ON.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result
    Result
    		Proceed to
    DTC B1630 and B1695 are not output
    		A
    DTC B1695 is output
    		B
    DTC B1630 is output
    		C


A
USE SIMULATION METHOD TO CHECK (Click here)

B
Go to step 3
C


2.CHECK REAR AIRBAG SENSOR RH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Supplemental Restraint Systems.Airbag System. Dtc B1630/23 Rear Airbag Sensor Rh Circuit Malfunction

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Temporarily replace the rear airbag sensor RH with a new one.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630 is not output.
    HINT:
    Codes other than DTC B1630 may be output at this time, but they are not related to this check.


NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE REAR AIRBAG SENSOR RH (Click here)

3.CHECK SIDE AIRBAG SENSOR LH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Supplemental Restraint Systems.Airbag System. Dtc B1630/23 Rear Airbag Sensor Rh Circuit Malfunction

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result
    Result
    		Proceed to
    DTC B1690 and B1695 are not output
    		A
    DTC B1695 is output
    		B
    DTC B1690 is output
    		C
    HINT:
    Codes other than DTC B1690 and B1695 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

REPLACE SIDE AIRBAG SENSOR LH (Click here)