Meter / Gauge System Data List / Active Test

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Meter Gauge Display. Land Cruiser. Urj200, 202 Grj200 Vdj200
  1. DATA LIST

  1. ACTIVE TEST

Meter / Gauge System -- Data List / Active Test



DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.

  5. According to the display on the GTS, read the Data List.

    Combination Meter
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tail Cancel SW
    TAIL cancel switch condition / ON or OFF
    ON: TAIL cancel switch on
    OFF: TAIL cancel switch off
    -
    ODO/TRIP Change SW
    Trip switch (ODO/TRIP switch) condition / ON or OFF
    ON: Trip switch (ODO/TRIP switch) pushed
    OFF: Trip switch (ODO/TRIP switch) not pushed
    -
    P-Seatbelt Buckle SW
    Front passenger side seat belt warning light request signal / ON or OFF
    ON: Tongue plate (for front passenger side) inserted
    OFF: Tongue plate (for front passenger side) not inserted
    -
    Vehicle Speed Meter
    Vehicle speed / Min.: 0 (0), Max.: 255 (158)
    Almost same as actual vehicle speed (when driving)
    Unit: km/h (mph)
    Engine Rpm
    Engine speed / Min.: 0, Max.: 12750 rpm
    Idling: 700 to 800
    Unit: rpm
    Coolant Temperature
    Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284) F
    After warming up: 80 to 105 (176 to 221)
    1. Unit: °C (°F).
    2. If the value is -40 (-40): The sensor circuit is open.
    3. If the value is 140 (284): The sensor circuit is shorted.
    Washer Switch
    Washer switch / ON or OFF
    ON: Washer switch on
    OFF: Washer switch off
    -
    Reverse Range Switch (6MT)
    Reverse lamp switch / ON or OFF
    ON: Reverse lamp switch on
    OFF: Reverse lamp switch off
    -
    Integrated value for Maintenance
    Integrated value for Maintenance / Min: 0, Max, 25500
    -
    -
    +B Voltage Value
    Battery voltage / Min.: 0 V, Max.: 25.5 V
    11 to 14 V
    -
    Oil Level SW
    Engine oil level switch/ ON or OFF
    ON: Engine oil level low
    OFF: Engine oil level not low
    -
    Water Level SW
    Level warning switch/ ON or OFF
    ON: Level warning switch on
    OFF: Level warning switch off
    -
    Fuel Input
    Fuel sender gauge input / Min.: 0, Max.: 127.5 L
    Fuel sender input value
    Unit: L
    Sub Fuel Input
    Fuel sender gauge input / Min.: 0, Max.: 127.5 L
    Fuel sender (for Sub Tank) input value
    Unit: L
    Ambient Temperature
    Outside temperature / Min: -40, Max: 87.5°C
    Outside temperature
    -
    Rheostat value
    Light control rheostat switch input / Min.: 0, Max.: 255
    Light control rheostat switch is fully turned right (0) → fully turned left (255)
    -
    Multi Switch (Down)
    Steering pad switch (Down) / ON or OFF
    ON: Steering pad switch (Down) pushed
    OFF: Steering pad switch (Down) released
    -
    Multi Switch (Menu)
    Steering pad switch (Menu) / ON or OFF
    ON: Steering pad switch (Menu) pushed
    OFF: Steering pad switch (Menu) released
    -
    Multi Switch (Enter)
    Steering pad switch (Enter) / ON or OFF
    ON: Steering pad switch (Enter) pushed
    OFF: Steering pad switch (Enter) released
    -
    Multi Switch (Right)
    Steering pad switch (Right) / ON or OFF
    ON: Steering pad switch (Right) pushed
    OFF: Steering pad switch (Right) released
    -
    Multi Switch (Left)
    Steering pad switch (Left) / ON or OFF
    ON: Steering pad switch (Left) pushed
    OFF: Steering pad switch (Left) released
    -
    Multi Switch (Up)
    Steering pad switch (Up) / ON or OFF
    ON: Steering pad switch (Up) pushed
    OFF: Steering pad switch (Up) released
    -
    Fuel Filter Switch
    Fuel filter assembly (clogging switch) / ON or OFF
    ON: Fuel filter assembly (clogging switch) on
    OFF: Fuel filter assembly (clogging switch) off
    for 1VD-FTV
    Turn Signal Switch (Right)
    Turn signal switch (right) / ON or OFF
    ON: Turn signal switch (right) on
    OFF: Turn signal switch (right) off
    -
    Turn Signal Switch (Left)
    Turn signal switch (left) / ON or OFF
    ON: Turn signal switch (left) on
    OFF: Turn signal switch (left) off
    -
    Hazard Flasher Switch
    Hazard warning signal switch / ON or OFF
    ON: Hazard warning signal switch on
    OFF: Hazard warning signal switch off
    -
    Passenger Occupant Detection Switch
    Front passenger side occupant detection sensor / ON or OFF
    ON: Front passenger seat occupied
    OFF: Front passenger seat not occupied
    -
    Turn Switch Signal (Full Turn)
    Turn signal switch status / ON or OFF
    ON: Turn signal switch on (Full Turn)
    OFF: Turn signal switch off
    -
    Multi Switch (Back)
    Steering pad switch (Back) / ON or OFF
    ON: Steering pad switch (Back) pushed
    OFF: Steering pad switch (Back) released
    -
    Battery Charge
    Battery Charge / OK or NG
    OK: Battery is charged
    NG: Battery is not charged
    -
    Driver Side Seatbelt Warning Buzzer
    Driver seat belt warning buzzer / ON or OFF
    Customized value displayed
    -
    P-Seatbelt Warning Buzzer
    Front Passenger Side Seatbelt Warning Buzzer / OFF or ON
    Customized value displayed
    -
    ODO Display Time After IG OFF Setting
    Condition of the ODO display time after the ignition switch is turned off / 30s, 60s, 600s, OFF
    Customized value displayed
    -
    Lane Change Flashing Times Setting
    Lane change flashing times customize status / OFF, 3 , 4, 5, :6, 7
    -
    This item is only to be used to display
    Flasher Sound Volume Adjustment
    Flasher sound volume customize status /Large, Medium, Small
    -
    This item is only to be used to display
    TPMS System
    Existence of function / with or without
    With: w/ Tire Pressure Warning System
    Without: w/o Tire Pressure Warning System
    -
    VGRS System
    Existence of function / with or without
    With: w/ VGRS System
    Without: w/o VGRS System
    -
    LDA System
    Existence of function / with or without
    With: w/ Lane Departure Alert System
    Without: w/o Lane Departure Alert System
    -
    PCS System
    Existence of function / with or without
    With: w/ Pre-collision System
    Without: w/o Pre-collision System
    -
    AHS System
    Existence of function / with or without
    With: w/ adaptive hi beam System
    Without: w/o adaptive hi beam System
    -
    Clearance Sonar System
    Existence of function / with or without
    With: w/ Clearance Sonar System
    Without: w/o Clearance Sonar System
    -
    Road Sign Assist System
    Existence of function / with or without
    With: w/ Road Sign Assistant System
    Without: w/o Road Sign Assistant System
    -
    Number of Trouble Code
    The number of the DTC currently stored / Min.: 0, Max.: 255
    0
    -

    Engine
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Rpm
    Engine speed / Min.: 0, Max.: 16383.75
    Idling: 700 to 800
    Unit: rpm
    Vehicle Speed Meter
    Vehicle speed / Min.: 0 (0), Max.: 255 (158)
    Actual vehicle speed
    1. Unit: km/h (mph)
    2. The speed is indicated on the speedometer.
    Coolant Temperature*1
    Engine coolant temperature:
    Min.: -40°C, Max.: 140°C
    80 to 100°C (176 to 212):
    After warming up
    1. If the value is -40°C (-40°F), The sensor circuit is open.
    2. If the value is 140°C (284°F) or higher, The sensor circuit is shorted.
    Coolant Temperature*2
    Engine coolant temperature /
    Min.: -40°C, Max.: 140°C
    After warming up engine: 75 to 90°C (167 to 194°F)
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.

    HINT:
    *1: except 1VD-FTV
    *2: for 1VD-FTV

ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (Combination Meter) / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Combination Meter
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation*1
    Speedometer
    0, 40, 80, 120, 160, 200, 240 or 280
    Acceptable range (mph or km/h): [Control range → Speedometer display]
    for km/h (for Australia)
    1. 40 → 41 to 45.5
    2. 80 → 81.4 to 85.8
    3. 120 → 122.1 to 126.8
    4. 160 → 163 to 168.2
    5. 200 → 203.9 to 209.5
    6. 240 → 244.8 to 250.8
    for km/h (except Australia)
    1. 40 → 41.7 to 46.2
    2. 80 → 83.4 to 88.4
    3. 120 → 125.1 to 130.6
    4. 160 → 166.2 to 173.2
    5. 200 → 207.7 to 215.7
    6. 200 → 249.2 to 258
    for mph
    1. 40 → 42 to 44.5
    2. 80 → 83.1 to 87.1
    3. 120 → 124.7 to 129.6
    Perform the test with the vehicle stopped and engine idling.
    Tachometer operation
    Tachometer
    0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000
    Perform the test with the vehicle stopped and engine idling.
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY, 1/2, FULL
    Perform the test with the vehicle stopped and engine idling.
    Volt Meter Operation
    Voltmeter
    0, 3, 6, 9, 12, 15 or 18
    Perform the test with the vehicle stopped and engine idling.
    Oil Pressure Meter Operation
    Oil pressure receiver gauge
    LOW, 1/4, 1/2, 3/4 or HIGH
    Perform the test with the vehicle stopped and engine idling.
    A/T Indicator operation (1)*10
    A/T indicator
    P, R, N, D, 4, 3, 2, L
    Perform the test with the vehicle stopped and engine idling.
    A/T Indicator operation (2)*10
    A/T indicator
    5, 6, 7, 8, S or M
    Perform the test with the vehicle stopped and engine idling.
    A/T Indicator operation (3)*10
    A/T indicator
    D
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Airbag
    SRS warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Doors All Open
    All doors open light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Driver Side Seat Belt
    Driver side seat belt warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Front Passenger Side Seat Belt
    Passenger side seat belt warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp ABS
    ABS warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Charge
    CHARGE warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Slip
    SLIP indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Tail
    TAIL indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Head
    HEAD indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Fr FOG
    Fr. FOG indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Rr FOG*16
    Rr. FOG indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Meter Display 1*2*14
    All dots in the multi-information display
    ALL, 0, 1, 2, 3, 4, 5 or 6
    Perform the test with the vehicle stopped and engine idling.
    Meter Display 2*2*14
    All dots in the multi-information display
    7, 8 or 9
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Beam
    BEAM indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Precrash
    PCS indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Headlamp Auto Leveling
    Headlight Auto Leveling light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Fuel
    Low fuel warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. TRC OFF
    TRC OFF indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Tire Pressure Warning System
    Tire pressure warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. ECONO
    Eco driving indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp ECT PWR*3,*7
    ECT PWR indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Cruise*7
    Cruise control indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Brake
    Brake warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Master Warning*14
    Master warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Park
    Parking brake warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. 2nd START*10
    2nd START indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Ctr DIFF LOCK
    Center differential lock indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Rr DIFF LOCK
    Rear differential lock indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. 4LO
    4LO indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. CRAWL*17
    CRAWL indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. SET*3,*7
    SET indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Radar Cruise Indicator*3
    Radar cruise control indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. VSC TRC
    TRC OFF indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. VSC OFF
    VSC OFF indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Automatic High Beam Indicator*9
    Automatic high beam indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    OFF Road Guidance Indicator
    Multi-terrain select indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    PPS Indicator
    PPS warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Turn Signal (Left) Indicator
    Turn L indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Turn Signal (Right) Indicator
    Turn R indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Check Engine Indicator
    MIL (Malfunction indicator lamp)
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Rr Inner Wheel Control Indicator
    Turn assist indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    BSM Control Indicator*18
    BSM control indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    LDA Control Indicator*19
    LDA control indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    RCTA Indicator*18
    RCTA indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    LOW, NORMAL or HIGH
    Perform the test with the vehicle stopped and engine idling.
    A/T Oil Temperature Operation*10*13
    A/T OIL TEMP warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Oil Level*13
    Oil level warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat GLOW*5
    Glow indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Lamp Washer*13
    Washer level warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Indicat. Over Speed*14
    Speed Limit indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Fuel Filter Indicator*5*13
    Fuel sedimenter warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Headlight warning light*13
    Headlight warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Smart System Indicator*13*15
    Smart Key indicator light (Illuminated Green)
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Smart System Warning*13*15
    Smart Key indicator light (Illuminated Yellow)
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Diesel Particulate Filter Warning*5*13
    DPF indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Brake Override Indicator*13
    Brake override indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.
    Go to Service Warning*13
    Go to service indicator light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling.

    HINT:
    *1:
    1. The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
    2. The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
    3. The needle position should be within the acceptable range.
    *2: If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.
    *3: w/ Dynamic Radar Cruise Control System
    *4: w/ Headlight Leveling
    *5: for 1VD-FTV
    *6: w/ VSC
    *7: w/ Cruise Control System
    *8: w/ Multi-terrain Select
    *9: w/ Automatic High Beam System
    *10: for Automatic Transmission
    *11: w/ Tire Pressure Warning System
    *12: w/ Multi-information Display
    *13: w/o Multi-information Display
    *14: for Middle East
    *15: w/ Entry and Start System
    *16: w/ Rear Fog light
    *17: w/ CRAWL control system
    *18: w/ Blind Spot Monitor System
    *19: w/ Lane Departure Alert System

Main Body
Tester Display
Test Part
Control Range
Diagnostic Note
Dimmer Signal
Illumination dimming operation
ON or OFF
-