Theft Deterrent System (W/ Entry And Start System) Glass Breakage Sensor Circuit

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING TECHSTREAM (GLASS BREAK SENSOR)

CHECK HARNESS AND CONNECTOR MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - GLASS BREAKAGE SENSOR AND BODY GROUND

INSPECT BACK DOOR GLASS

THEFT DETERRENT SYSTEM (w/ Entry and Start System) - Glass Breakage Sensor Circuit


DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window glass LH or quarter window glass RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Theft Deterrent System (W/ Entry And Start System) Glass Breakage Sensor Circuit


INSPECTION PROCEDURE

  1. If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
  2. w/ Door Control Battery:
    As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (Click here).
1.READ VALUE USING TECHSTREAM (GLASS BREAK SENSOR)

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.


Main Body
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Glass break sensor detection
Glass breakage sensor detection / With or Without1
With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-
OK:
"With" (glass breakage sensor operating) appears on Techstream screen.
Result
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] (Click here)

C
Go to step 2
A

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] (Click here)

2.CHECK HARNESS AND CONNECTOR MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - GLASS BREAKAGE SENSOR AND BODY GROUND

  1. Disconnect the E118 main body ECU (multiplex network body ECU) connector.

  1. Disconnect the S37 back door glass (glass breakage sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E118-7 (GPBS) - S37-1 (SSR+)
    		Always
    		Below 1 Ω
    E118-7 (GPBS) - Body ground
    		Always
    		10 kΩ or higher
    S37-1 (SSR+) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT BACK DOOR GLASS


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Theft Deterrent System (W/ Entry And Start System) Glass Breakage Sensor Circuit

  1. Disconnect the S37 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    S37-1 (SSR+) - S18-1 (E)
    		Always
    		Below 1 Ω
    Result
    Result
    		Proceed to
    OK (for LHD)
    		A
    OK (for RHD)
    		B
    NG
    		C


B
REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] (Click here)

C
REPLACE BACK DOOR GLASS (Click here)
A

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] (Click here)