Theft Deterrent System (W/ Entry And Start System) Data List / Active Test

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. DATA LIST

  1. ACTIVE TEST

Theft Deterrent System (W/ Entry And Start System) -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on intelligent tester, read the "Data List".

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Intrusion sensor OFF
    		Intrusion sensor cancel switch /
    ON or OFF
    		ON: Intrusion sensor active (switch off)
    OFF: Intrusion sensor not active (switch on)
    		-
    Intrusion sensor detection
    		Intrusion sensor setting /
    ON or OFF
    		ON: Moving object detected by sensor during arming preparation state to armed state
    OFF: No moving object detected by sensor
    		-
    Tilt sensor detection
    		Tilt sensor setting /
    ON or OFF
    		ON: Tilt sensor set
    OFF: Tilt sensor not set
    		-
    Hood Courtesy Switch
    		Engine hood courtesy switch /
    ON or OFF
    		ON: Engine hood open
    OFF: Engine hood closed
    		-
    Warn By Horn
    		Security horn /
    ON or OFF
    		ON: Security horn sounding
    OFF: Security horn not sounding
    		-
    Glass break sensor detection
    		Glass breakage sensor detection /
    ON or OFF
    		ON: Glass breakage sensor operates
    OFF: Glass breakage sensor does not operate
    		-
    Pattern Glass Connection
    		Pattern Glass Connection /
    OK or NG
    		OK: Pattern glass connection
    NG: No pattern glass connection
    		-
    Intrusion sensor 1 communication
    		Intrusion sensor setting /
    OK or STOP
    		OK: Intrusion sensor set
    STOP: Intrusion sensor not set
    		-
    Tilt sensor communication
    		Tilt sensor setting /
    OK or STOP
    		OK: Tilt sensor set
    STOP: Tilt sensor not set
    		-
    Tilt sensor OFF Switch
    		Tilt sensor OFF switch /
    ON or OFF
    		ON: Tilt sensor active (switch off)
    OFF: Tilt sensor not active (switch on)
    		-
    # Codes
    		Number of diagnostic trouble codes
    		-
    		-

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    D Door Courtesy SW
    		Driver side door courtesy light switch signal / ON or OFF
    		ON: Driver side door opened
    OFF: Driver side door closed
    		-
    D Door Lock Pos SW
    		Driver side door lock position switch signal / ON or OFF
    		ON: Driver side door unlocked
    OFF: Driver side door locked
    		-
    Door Key SW-Lock
    		Door key linked lock switch signal / ON or OFF
    		ON: Driver side door key cylinder turned to lock position
    OFF: Driver side door key cylinder not turned
    		-
    D-Door Key SW-UL
    		Door key linked unlock switch signal / ON or OFF
    		ON: Driver side door key cylinder turned to unlock position
    OFF: Driver side door key cylinder not turned
    		-
    P-Door Courtesy SW
    		Front passenger side door courtesy light switch signal / ON or OFF
    		ON: Front passenger side door opened
    OFF: Front passenger side door closed
    		-
    P-Door Lock Pos SW
    		Front passenger side door lock position switch signal / ON or OFF
    		ON: Front passenger side door unlocked
    OFF: Front passenger side door locked
    		-
    Door Lock SW-Lock
    		Door manual lock switch signal / ON or OFF
    		ON: Front passenger side door control switch on (LOCK)
    OFF: Front passenger side door control switch off
    		-
    Door Unlock SW-Unlock
    		Door manual unlock switch signal / ON or OFF
    		ON: Front passenger side door control switch on (UNLOCK)
    OFF: Front passenger side door control switch off
    		-
    RL Door Courtesy SW
    		Rear LH side door courtesy light switch signal / ON or OFF
    		ON: Rear LH side door opened
    OFF: Rear LH side door closed
    		-
    RL-Door Lock Pos SW
    		Rear LH side door lock position switch signal / ON or OFF
    		ON: Rear LH side door unlocked
    OFF: Rear LH side door locked
    		-
    RR Door Courtesy SW
    		Rear RH side door courtesy light switch signal / ON or OFF
    		ON: Rear RH side door opened
    OFF: Rear RH side door closed
    		-
    RR-Door Lock Pos SW
    		Rear RH side door lock position switch signal / ON or OFF
    		ON: Rear RH side door unlocked
    OFF: Rear RH side door locked
    		-
    Back Door Courtesy SW
    		Back door courtesy light switch signal / ON or OFF
    		ON: Back door open
    OFF: Back door closed
    		-
    Back Door Open SW
    		ON / OFF
    		ON: Back door opener switch on
    OFF: Back door opener switch off
    		-
    Back Door Open
    		Permit / Prohibit
    		PERMIT: Back door open available
    PROHIBIT: Back door open unavailable
    		-
    IG SW
    		ON / OFF
    		ON: Engine switch is on (IG)
    OFF: Engine switch is off
    		-
    ACC SW
    		ON / OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-


ACTIVE TEST
HINT:
Using the intelligent tester to perform the Active Test allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry&Start / Active Test.

  5. According to the display on intelligent tester, perform the "Active Test".

    Entry&Start
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Security Indicator
    		Security indicator
    		ON / OFF
    		-
    Security Horn*1
    		Security horn
    		ON / OFF
    		-
    Security Horn2*2
    		Theft warning siren (self power siren)
    		ON / OFF
    		-
    Power For Tilt Sensor*3
    		Tilt sensor power supply
    		ON / OFF
    		-
    Power For Intrusion Sensor*3
    		Intrusion sensor power supply
    		ON / OFF
    		-

    HINT:
    *1: w/ Security Horn
    *2: w/ Theft Warning Siren (Self Power Siren)
    *3: w/ Intrusion Sensor