Engine Immobiliser System (W/ Entry And Start System) Data List / Active Test

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Engine Immobiliser System (W/ Entry And Start System) -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry&Start / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Ignition Switch
    		Engine switch on (IG) signal / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    #Codes
    		Number of trouble codes / Min: 0, Max: 255
    		-
    		-
    Immobiliser
    		Engine immobiliser system status / Set or Unset
    		Set: Key not in cabin
    Unset: Key in cabin
    		-
    Master Key
    		Master key code signal / Match or No Match
    		Match: Master key code is sent
    No Match: Unmatched master key code sent
    		-
    BCC Malfunction
    		Transponder chip signal / OK or NG
    		OK: Correct data sent
    NG: Incorrect data sent
    		-
    Abnormal Status
    		Transponder chip data / OK or NG
    		OK: Data OK
    NG: Data error
    		-
    Different Encrypt Code
    		Transponder chip signal / OK or NG
    		OK: Correct data sent
    NG: Incorrect data sent
    		-
    Different Serial Number
    		Transponder chip signal / OK or NG
    		OK: Correct data sent
    NG: Incorrect data sent
    		-
    Frame Error
    		Transponder chip signal / OK or NG
    		OK: Correct data sent
    NG: Incorrect data sent
    		-
    Response
    		Transponder chip signal / OK or NG
    		OK: Correct data sent
    NG: Incorrect data sent
    		-
    ID-BOX Sleep Condition
    		ID code box condition / Yes or No
    		Yes: ID code box in sleep condition
    No: ID code box not in sleep condition
    		-
    ID-BOX Start Condition
    		ID code box condition / Yes or No
    		Yes: ID code box sends wake up signal
    No: ID code box does not send wake up signal
    		-
    Engine Start Request
    		ID code box start request condition / OK or NG
    		OK: Start request condition signal received (past)
    NG: Start request condition signal not received (past)
    		-
    S Code Check
    		S code verification result / OK or NG
    		OK: Verification confirmed
    NG: Verification not confirmed
    		-
    L Code Check
    		L code verification result / OK or NG
    		OK: Verification confirmed
    NG: Verification not confirmed
    		-
    Unlock Request Receive
    		Steering unlock command reception status / OK or NG
    		OK: Steering unlock request received
    NG: Steering unlock request not received
    		-
    Lock Request Receive
    		Steering lock command reception status / OK or NG
    		OK: Steering lock request received
    NG: Steering lock request is not received
    		-
    S Code Check (Past)
    		S code verification result (past) / OK or NG
    		OK: Verification confirmed (past)
    NG: Verification not confirmed (past)
    		-
    L Code Check (Past)
    		L code verification result (past) / OK or NG
    		OK: Verification confirmed (past)
    NG: Verification not confirmed (past)
    		-
    EFI Code Receive
    		SFI*1 or ECD*2 code receive (when DTC stored) / OK or NG
    		OK: SFI*1 or ECD*2 code received
    NG: SFI*1 or ECD*2 code not received
    		-
    EFI communication
    		SFI*1 or ECD*2 communication / OK or NG
    		OK: SFI*1 or ECD*2 communication normal
    NG: SFI*1 or ECD*2 communication abnormal
    		-

    HINT:
    1. *1: for 1GR-FE, 1UR-FE, 3UR-FE
    2. *2: for 1VD-FTV

PERFORM ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry&Start / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Entry&Start
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Security Indicator
    		Security indicator light
    		ON or OFF
    		-