Entry And Start System (For Start Function) Data List / Active Test

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Entry And Start System (For Start Function) -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ACC SW
    		Engine switch on (ACC)/ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    IG SW
    		Engine switch on (IG)/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Stop Light SW
    		Stop light switch/ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Start Switch1
    		Start switch 1/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Start Switch2
    		Start switch 2/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Steering Unlock Switch
    		Steering lock condition/ON or OFF
    		ON: Steering unlocked
    OFF: Steering locked
    		-
    Neutral SW/ Clutch SW
    		Park/neutral position switch (A/T), clutch start switch (M/T)/ON or OFF
    		ON: Shift lever in P or N (A/T), clutch pedal depressed (M/T)
    OFF: Shift lever not in P or N (A/T), clutch pedal released (M/T)
    		-
    Shift P Signal
    		Shift P position signal/ON or OFF
    		ON: Shift lever in P
    OFF: Shift lever not in P
    		-
    Vehicle Speed Signal
    		Vehicle speed signal/STOP or RUN
    		STOP: Vehicle stopped
    RUN: Vehicle running
    		-
    Engine Condition
    		Engine condition/STOP or RUN
    		STOP: Engine stopped
    RUN: Engine running
    		-
    IG1 Relay Monitor(Outside)
    		IG1 No. 3 relay outer relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Monitor(Outside)
    		Integration relay (IG2 relay) outer relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG1 Relay Monitor(Inside)
    		IG1 No. 3 relay inner relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Monitor(Inside)
    		Integration relay (IG2 relay) inner relay monitor/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    ACC Relay Monitor
    		ACC relay monitor/ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    Latch Circuit
    		Latch circuit/ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off, on (ACC)
    		-
    Starter Request Signal
    		Starter request signal/ON or OFF
    		ON: ST relay ON
    OFF: ST relay OFF
    		-
    Power Supply Condition
    		Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON
    		ALL OFF: All relays OFF
    ACC ON: ACC relay ON
    IG2 ON: Integration relay (IG2 relay) ON
    ST ON: STSW signal ON
    		-
    ACC Relay Cut Signal
    		ACC relay cut signal/ON or OFF
    		ON: Engine cranking
    OFF: Engine not cranking
    		-
    Starter Relay Monitor
    		ST relay monitor/ON or OFF
    		ON: Engine cranking
    OFF: Engine not cranking
    		-
    Communication Smart/Wireless
    		Communication to certification ECU (smart key ECU assembly)/OK or STOP
    		OK: Communication
    STOP: No communication
    		-
    The Number of DTC
    		Number of diagnostic trouble codes/Min: 0, Max: 255
    		-
    		-

    Entry & Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Ignition Switch
    		Engine switch/ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Unmatched Vehicle-ID
    		Key ID/YES or NO
    		YES: Key ID matches
    NO: Key ID differs
    		-
    No Response
    		No Communication condition between vehicle and electrical key transmitter (response) / Yes or No
    		Yes: Key ID code not matched to vehicle
    No: Key ID code matched to vehicle
    		-
    Unmatch Code or Form
    		Code format/YES or NO
    		YES: Code format matches
    NO: Code format differs
    		-
    Key Low Battery
    		Key battery conditions/Yes or No
    		Yes: Key battery voltage low
    No: Key battery voltage normal
    		-
    #Codes
    		Number of diagnostic trouble codes/Min: 0, Max: 255
    		-
    		-
    ID Code Difference(Resp)
    		ID code/YES or NO
    		YES: ID code matches
    NO: ID code differs
    		-
    C Code Difference
    		Challenge code/YES or NO
    		YES: Challenge code matches
    NO: Challenge code differs
    		-
    Engine Start Condition
    		Engine start condition by certification ECU (smart key ECU assembly)/OK or NG
    		OK: Engine start permitted
    NG: Engine start prohibited
    		-
    S Code Check
    		S code certification result/NG or OK
    		OK: S code certification result normal
    NG: S code certification result abnormal
    		-
    L Code Check
    		L code certification result/NG or OK
    		OK: L code certification result normal
    NG: L code certification result abnormal
    		-
    Ignition Available Area
    		Key area where engine start is possible/All or Front
    		All: All areas
    Front: Front only
    		-


PERFORM ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Indicator for Lighting
    		Indicator illumination
    		ON/OFF
    		-
    Indicator Condition
    		Indicator light illumination pattern
    		Green/Amber/No Sig
    		-
    P Supply for Steering Lock
    		Steering lock ECU power supply
    		ON/OFF
    		-

    Entry & Start
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Fr-Seat Inside Transmitter
    		Indoor key antenna (for front)
    		ON/OFF
    		-
    Rr-Seat Inside Transmitter
    		Indoor key antenna (for rear1)
    		ON/OFF
    		-
    Inside Trunk/Backdoor Transmitter
    		Indoor key antenna (for rear2)
    		ON/OFF
    		-
    Outside Trunk/Backdoor Transmitter
    		Electrical key antenna
    		ON/OFF
    		-