Entry And Start System (For Entry Function) Back Door Entry Unlock Function Does Not Operate

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK POWER DOOR LOCK CONTROL SYSTEM

READ VALUE USING GTS (B-DR OPENING OPERATION)

READ VALUE USING GTS (TR/B DOOR UNLOCK SW)

CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)

ENTRY AND START SYSTEM (for Entry Function) - Back Door Entry Unlock Function does not Operate


DESCRIPTION

If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the open switch (connection between the back door opener switch assembly and certification ECU [smart key ECU assembly]).

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Back Door Entry Unlock Function Does Not Operate


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (Click here).
  2. When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (Click here).
  5. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
1.CHECK POWER DOOR LOCK CONTROL SYSTEM

  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.


NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING GTS (B-DR OPENING OPERATION)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Entry&Start / Data List.

  1. Read the Data List according to the display on the GTS.

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    B-Dr Opening Operation
    		Back door opening operation / Long, Twice or OFF
    		Customize setting displayed
    		-
    Result
    Result
    		Proceed to
    Customize setting is Long or Twice
    		A
    Customize setting is OFF
    		B


B
PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters) (Click here)
A


3.READ VALUE USING GTS (TR/B DOOR UNLOCK SW)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Entry&Start / Data List.

  1. Read the Data List according to the display on the GTS.

    Entry&Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Tr/B-Door Unlock SW
    		Back door opener switch assembly (open switch) / ON or OFF
    		ON: Back door opener switch assembly (open switch) pressed
    OFF: Back door opener switch assembly (open switch) not pressed
    1. Displays whether the back door opener switch assembly (open switch) is on or off.
    2. Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.
    OK:
    The GTS display changes correctly in response to the operation of the back door opener switch assembly.


NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

  1. Disconnect the S7 back door opener switch assembly connector.

  1. Disconnect the E129 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    S7-3 (UL) - E129-5 (TSW5)
    		Always
    		Below 1 Ω
    S7-3 (UL) or E129-5 (TSW5) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)

  1. Remove the back door opener switch assembly (Click here).

  1. Inspect the back door opener switch assembly (Click here).



NG
REPLACE BACK DOOR OPENER SWITCH ASSEMBLY (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)