Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ENTRY AND START SYSTEM (ENTRY FUNCTION)

CHECK ENTRY AND START SYSTEM (START FUNCTION)

CHECK WAVE ENVIRONMENT

KEY DIAGNOSTIC MODE

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

CHECK INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor)

ENTRY AND START SYSTEM (for Entry Function) - Room Oscillator does not Recognize Key


DESCRIPTION

If the room oscillator does not recognize the key, one of the following may be the cause: 1) communication between the indoor electrical key antenna (for Front) and electrical key transmitter cannot be performed; or 2) communication between the indoor electrical key antenna (for Rear 1) and electrical key transmitter cannot be performed; or 3) communication between the indoor electrical key antenna (for Rear 2) and electrical key transmitter cannot be performed.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key


INSPECTION PROCEDURE

NOTICE:
  1. Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.
1.CHECK ENTRY AND START SYSTEM (ENTRY FUNCTION)

  1. Check that the entry lock and unlock function can be operated at each door (Click here).



NG
Go to DTC OF OTHER COMPONENTS (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR) (Click here)
OK


2.CHECK ENTRY AND START SYSTEM (START FUNCTION)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Remove the battery of the electrical key transmitter (Click here).

  1. With the brake pedal depressed, touch the key to the engine switch, as shown in the illustration.

  1. When operating the engine switch, check whether the power source mode changes.

    OK:
    Power source mode changes.
    HINT:
    1. When the electrical key transmitter cannot be verified even though it is in the operating range of the start function, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.
    2. When performing the check, if the power source mode changes, there is a problem with key certification inside the cabin.


NG
Go to ENTRY AND START SYSTEM (Power Source Mode does not Change) (Click here)
OK


3.CHECK WAVE ENVIRONMENT

  1. Install the battery to the electrical key transmitter (Click here).

  1. Bring the electrical key transmitter near the indoor electrical key antenna (in center console), and perform an engine control system start check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the center console, communication is not possible.
    OK:
    Engine starts.

  1. Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 1 seat cushion), and perform an engine control system start check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the rear No. 1 seat cushion, communication is not possible.
    OK:
    Engine starts.

  1. Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 2 seat cushion), and perform an engine control system start check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the rear No. 2 seat cushion, communication is not possible.
    HINT:
    1. When the electrical key transmitter is brought near the indoor electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference, If installed, remove them and perform the operation check.
    OK:
    Engine starts.


NG
Go to step 4
OK

AFFECTED BY WAVE INTERFERENCE

4.KEY DIAGNOSTIC MODE


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Diagnostic mode inspection (indoor electrical key antenna (for Front)).

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Front Room.

    5. When the electrical key transmitter is placed on the driver seat or front passenger seat cushion, check that the wireless door lock buzzer sounds.



    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Diagnostic mode inspection (indoor electrical key antenna (for Rear 1)).

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Rear Room.

    5. When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.



    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Diagnostic mode inspection (indoor electrical key antenna (for Rear 2)).

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Back Door (inside) Room.

    5. When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.

HINT:
  1. If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
  2. It is possible to check which indoor electrical key antenna (front, rear 1 or rear 2) is operating by sounding the buzzer.
  3. If the buzzer does not sound for any indoor electrical key antennas, the certification ECU (smart key ECU assembly) circuit may have a malfunction.
Result
Result
Proceed to
Front operation check fails
A
Rear 1 operation check fails
B
Rear 2 operation check fails
C
Front, rear 1 and rear 2 operation checks are normal or fail
D


B
Go to step 7

C
Go to step 9

D
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Disconnect the E29 ECU connector.

  1. Disconnect the V3 antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    V3-1 (CLG3) - E29-11 (CLG5)
    		Always
    		Below 1 Ω
    V3-3 (CLGB) - E29-12 (CG5B)
    		Always
    		Below 1 Ω
    V3-1 (CLG3) - Body ground
    		Always
    		10 kΩ or higher
    V3-3 (CLGB) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Measure the voltage according to the value(s) in the table below.

    OK:
    Tester Connection
    		Tool Setting
    		Switch Condition
    		Specified Condition
    E29-11 (CLG5) - E29-12 (CG5B)
    		2 V/DIV, 2 μsec./DIV. (Reference)
    		Engine switch on (IG)
    		Pulse generation


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Front Floor) (Click here)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Disconnect the E29 ECU connector.

  1. Disconnect the L8 antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    L8-1 (CLG4) - E29-13 (CLG6)
    		Always
    		Below 1 Ω
    L8-2 (CLGB) - E29-14 (CG6B)
    		Always
    		Below 1 Ω
    L8-1 (CLG4) - Body ground
    		Always
    		10 kΩ or higher
    L8-2 (CLGB) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Measure the voltage according to the value(s) in the table below.

    OK:
    Tester Connection
    		Tool Setting
    		Switch Condition
    		Specified Condition
    E29-13 (CLG6) - E29-14 (CG6B)
    		2 V/DIV., 2 μsec./DIV. (Reference)
    		Engine switch on (IG)
    		Pulse generation


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor) (Click here)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Disconnect the E29 ECU connector.

  1. Disconnect the L9 antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    L9-1 (CLG6) - E29-15 (CLG)
    		Always
    		Below 1 Ω
    L9-2 (CLGB) - E29-16 (CG7B)
    		Always
    		Below 1 Ω
    L9-1 (CLG6) - Body ground
    		Always
    		10 kΩ or higher
    L9-2 (CLGB) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor)

Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Room Oscillator Does Not Recognize Key

  1. Measure the voltage according to the value(s) in the table below.

    OK:
    Tester Connection
    		Tool Setting
    		Switch Condition
    		Specified Condition
    E29-15 (CLG7) - E29-16 (CG7B)
    		2 V/DIV., 2 μsec./DIV. (Reference)
    		Engine switch on (IG)
    		Pulse generation


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor) (Click here)