Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate

Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Theft Deterrent Keyless Entry. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK POWER DOOR LOCK OPERATION

READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)

CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE)

INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side)

REPLACE DOOR ELECTRICAL KEY OSCILLATOR

CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

ENTRY AND START SYSTEM (for Entry Function) - Front Passenger Side Door Entry Lock Function does not Operate


DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle (entry lock switch) → front passenger side door electrical key oscillator).

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate


INSPECTION PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION

  1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.


NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    P Door Lock Position SW
    		Front passenger side door lock position switch signal / ON or OFF
    		ON: Front passenger side door unlocked
    OFF: Front passenger side door locked
    		-
    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.


NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)

  1. Using the intelligent tester, read the Data List.

    Entry & Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    P-Door Trigger Switch
    		Front passenger side door outside handle lock switch / ON or OFF
    		ON: Entry lock switch pushed
    OFF: Entry lock switch not pushed
    		-
    OK:
    On tester screen, item changes between ON and OFF according to above chart.


NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate

  1. Disconnect the z22 or z24 oscillator connector.

  1. Disconnect the z21 or z23 handle connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    		Condition
    		Specified Condition
    z22-9 (TRG-) - z21-1 (TRG-)
    		Always
    		Below 1 Ω
    z22-9 (TRG-) - Body ground
    		Always
    		10 kΩ or higher
    for RHD:
    Tester Connection
    		Condition
    		Specified Condition
    z24-9 (TRG-) - z23-1 (TRG-)
    		Always
    		Below 1 Ω
    z24-9 (TRG-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate

  1. Disconnect the E29 ECU connector.

  1. Disconnect the z21 or z23 handle connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    		Condition
    		Specified Condition
    E29-4 (TSW2) - z21-3 (TRG+)
    		Always
    		Below 1 Ω
    E29-4 (TSW2) - Body ground
    		Always
    		10 kΩ or higher
    for RHD:
    Tester Connection
    		Condition
    		Specified Condition
    E29-4 (TSW2) - z23-3 (TRG+)
    		Always
    		Below 1 Ω
    E29-4 (TSW2) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Theft Deterrent Keyless Entry.Entry And Start System (For Entry Function).Entry And Start System (For Entry Function) Front Passenger Side Door Entry Lock Function Does Not Operate

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    		Switch Condition
    		Specified Condition
    z21-1 (TRG-) - z21-3 (TRG+)
    		Lock switch not pushed
    		10 kΩ or higher
    Lock switch pushed
    		Below 1 Ω
    for RHD:
    Tester Connection
    		Switch Condition
    		Specified Condition
    z23-1 (TRG-) - z23-3 (TRG+)
    		Lock switch not pushed
    		10 kΩ or higher
    Lock switch pushed
    		Below 1 Ω


NG
REPLACE FRONT DOOR OUTSIDE HANDLE (Click here)
OK


7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR

  1. Replace the door electrical key oscillator (Click here).


NEXT


8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

  1. Check that the entry function operates normally.

    OK:
    Operates normally.


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)