Vehicle Interior. Land Cruiser. Urj200, 202 Grj200 Vdj200
Door Lock. Land Cruiser. Urj200, 202 Grj200 Vdj200
Back Door Lock -- Inspection |
| 1. INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door) |
Check the operation of the door lock motor.
Text in Illustration *1 Latch *a Open *b Close *c Component without harness connected
(Back Door Lock Assembly)Move the back door lock assembly to the close position.
Apply battery voltage to the door lock motor assembly and check the operation of the door lock motor.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 1 (ACT+)
Battery negative (-) → 2 (ACT-)Close → Open
 |
| 2. INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door) |
Check the operation.
Text in Illustration *a Component without harness connected
(Back Door Lock Assembly)*b Close Operation Direction *c Open Operation Direction Apply battery voltage and check the operation of the closer motor.
- OK:
Battery Connection Result Battery positive (+) → 1 (M-)
Battery negative (-) → 2 (M+)Close Operation Battery positive (+) → 2 (M+)
Battery negative (-) → 1(M-)Open Operation
 |
Check the resistance of the half latch switch.
Text in Illustration *a Component without harness connected
(Back Door Lock Assembly)*b Open Position *c Half-latch Position *d Full-latch Position *e Over Stroke Position Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 3 (CLS) - 1 (E) Open position Below 1 Ω 3 (CLS) - 1 (E) Open position → Half-latch position Below 1 Ω → 10 kΩ to higher 3 (CLS) - 1 (E) Half-latch position 10 kΩ to higher 3 (CLS) - 1 (E) Full-latch position 10 kΩ to higher 3 (CLS) - 1 (E) Over Stroke Position 10 kΩ to higher
 |
Check the resistance of the full latch switch.
Text in Illustration *a Component without harness connected
(Back Door Lock Assembly)*b Open Position *c Half-latch Position *d Full-latch Position *e Over Stroke Position Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 4 (CTY) - 1 (E) Open position Below 1 Ω 4 (CTY) - 1 (E) Half-latch position Below 1 Ω 4 (CTY) - 1 (E) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ to higher 4 (CTY) - 1 (E) Full-latch position 10 kΩ to higher 4 (CTY) - 1 (E) Over Stroke Position 10 kΩ to higher
 |
Check the resistance of the pawl switch.
Text in Illustration *a Component without harness connected
(Back Door Lock Assembly)*b Open Position *c Half-latch Position *d Full-latch Position *e Over Stroke Position Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 2 (POLE) - 1 (E) Open position Below 1 Ω 2 (POLE) - 1 (E) Open position → Half-latch position 10 kΩ to higher → Below 1 Ω → 10 kΩ to higher 2 (POLE) - 1 (E) Half-latch position 10 kΩ to higher 2 (POLE) - 1 (E) Half-latch position → Full-latch position 10 kΩ to higher → Below 1 Ω → 10 kΩ to higher 2 (POLE) - 1 (E) Full-latch position 10 kΩ to higher 2 (POLE) - 1 (E) Over Stroke Position 10 kΩ to higher
 |
Check the resistance of the sector switch.
Text in Illustration *a Component without harness connected
(Back Door Lock Assembly)*b Sector Gear in Neutral Position Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 6 (OPN) - 1 (E) Sector gear in neutral position (Sector switch on) Below 1 Ω 6 (OPN) - 1 (E) Sector gear in neutral position (Sector switch off) 10 kΩ to higher
 |