Blind Spot Monitor System Operation Check

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

NOTICE:

1. Perform this inspection on level ground.
   
2. Make sure that there are no metal objects around the vehicle or on the ground.
   
3. Unload the vehicle before beginning the inspection.
   
4. Confirm that the tire pressure is correct before beginning the inspection.
   
5. Do not place any objects other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 6 m (19.68 ft.) x L 6 m (19.68 ft.) x H 4 m (13.12 ft.)) shown in the illustration.
   

Place the reflector.

1. From the center of the rear bumper (center of the emblem), hang a weight with a pointed tip, and mark position on the ground (mark A).
   

   
   
   
   
   

   Text in Illustration

   *a	String	*b	Weight
   *c	Center point	*d	Same size

   HINT:

   Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.





2. From the center of the front bumper (center of the emblem), hang a weight with a pointed tip, and mark position on the ground (mark B).
   

   
   
   
   
   

   Text in Illustration

   *a	String	*b	Weight
   *c	Center point	*d	Same size

   HINT:

   Lightly flick the string with your fingers several times to confirm that the string is aligned with mark (B).





3. Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).
   





4. Enlarge and print out the poster shown in the illustration.
   

   
   
   
   




5. Attach the printed poster to the floor with the vehicle center line aligned with point A as shown in the illustration.
   





6. Attach strings aligned with the lines labeled C and mark points D at a distance of 3484 mm (11.43 ft.) from point A.
   





7. Set the reflector at the position (E) or (F) shown in the illustration below.
   

   SST

   09870-60000(09870-60010)
   09870-60040
   

   
   
   
   

   NOTICE:

   
   
   1. Set the reflector so that its center is 882 mm (2.89 ft) above the ground.
      
   
   
   2. The center of triangular pyramid is the reference point for the setting position and angle.
      
   3. Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.
      
   4. Perform the operation as precisely as possible.
      

Perform the blind spot monitor beam axis display.

1. Connect the GTS to the DLC3.
   

2. Turn the engine switch on (IG).
   

3. Turn the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) on.
   

4. Turn the GTS on.
   

5. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.
   

6. Check the results displayed for the BSM beam axis display.
   

   Allowable Range:

   Item	Blind Spot Monitor Sensor LH (Master)	Blind Spot Monitor Sensor RH (Slave)
   Angle	-3.6 to +3.6 °	-3.6 to +3.6 °

   HINT:

   If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.

7. Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.
   

   HINT:

   When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.

Remove the rear bumper.

1. for Standard : Click here
   
2. w/ Towing Hitch : Click here
   
3. w/ Pintle Hook : Click here
   

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:

Dimension	Specified Value
y	78 to 87 mm (3.07 to 3.43 in)

Degree	Specified Value
A	46 to 54°