Navigation System How To Proceed With Troubleshooting

Audio Visual Telematics. Land Cruiser. Urj200, 202 Grj200 Vdj200
Navigation Multi Info Display. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. VEHICLE BROUGHT TO WORKSHOP

  2. CUSTOMER PROBLEM ANALYSIS

  3. INSPECT BATTERY VOLTAGE

  4. CHECK CABIN

  5. CHECK NAVIGATION SYSTEM NORMAL CONDITION

  6. CHECK CAN COMMUNICATION SYSTEM*

  7. CHECK FOR DTC*

  8. CLEAR DTC*

  9. RECHECK FOR DTC*

  10. DIAGNOSTIC TROUBLE CODE CHART

  11. CHECK HARD DISC

  12. PROBLEM SYMPTOMS TABLE

  13. PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

  14. CHECK CIRCUIT

  15. RECHECK FOR DIAGNOSTIC TROUBLE CODE*

  16. PERFORM CONFIRMATION TEST

Navigation System -- How To Proceed With Troubleshooting


HINT:
  1. Use the following procedure to troubleshoot the navigation system.
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS
      1. When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference.
        Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points in problem analysis:

        What
        		Vehicle model, system name
        When
        		Date, time, occurrence frequency
        Where
        		Road conditions
        Under what conditions?
        		Driving conditions, weather conditions
        How did it happen?
        		Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE

    1. Measure the battery voltage with the engine switch off.

      Standard voltage:
      11 to 14 V
      1. If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

    NEXT


    4.CHECK CABIN

    1. Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

      OK:
      Condensation is not likely being produced and the temperature is not high or extremely low.
      HINT:
      1. A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
      2. The navigation system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.


    		NG.
    SET CABIN TO APPROPRIATE TEMPERATURE
    OK


    5.CHECK NAVIGATION SYSTEM NORMAL CONDITION

    1. Refer to Check System Normal Condition (Click here).

      Result
      Result
      		Proceed to
      Symptom is not normal operation.
      		A
      Symptom is normal operation.
      		B



    		B.
    SYMPTOM IS NORMAL OPERATION
    A


    6.CHECK CAN COMMUNICATION SYSTEM*

    1. Check for DTC output.

      1. for LHD: Click here
      2. for RHD: Click here
      Result
      Result
      		Proceed to
      CAN DTCs are not output.
      		A
      CAN DTCs are output (for LHD).
      		B
      CAN DTCs are output (for RHD).
      		C


    		B.
    GO TO CAN COMMUNICATION SYSTEM (Click here)

    		C.
    GO TO CAN COMMUNICATION SYSTEM (Click here)
    A


    7.CHECK FOR DTC*

    1. Refer to DTC Check/Clear (Click here).

      Result
      Result
      		Proceed to
      DTCs are output.
      		A
      DTCs are not output.
      (The multi-display displays content.)
      		B
      DTCs are not output.
      (The multi-display does not display anything.)
      		C

      HINT:
      If more information is needed, perform a check using the "System Check Mode" screen after checking for DTCs using the intelligent tester.


    		B.
    Go to step 11

    		C.
    Go to step 12
    A


    8.CLEAR DTC*

    1. Refer to DTC Check/Clear (Click here).

      HINT:
      The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.

    NEXT


    9.RECHECK FOR DTC*

    1. Refer to DTC Check/Clear (Click here).

      Result
      Result
      		Proceed to
      DTCs are output.
      		A
      DTCs are not output.
      		B

      HINT:
      1. Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
      2. If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester.
      3. Check the DTCs and inspect the area that the code indicates.


    		B.
    Go to step 11
    A


    10.DIAGNOSTIC TROUBLE CODE CHART

    1. Find the output code in Diagnostic Trouble Code Chart (Click here).

      NOTICE:
      1. The navigation system outputs DTCs for the following system.
      2. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
      3. Refer to Audio and Visual System (w/ Navigation System) (Click here)
      4. Refer to Rear Seat Entertainment System (Click here)
      Result
      Result
      		Proceed to
      DTCs for the navigation system are output.
      		A
      DTCs for the audio and visual system (w/ Navigation System) are output.
      		B
      DTCs for the rear seat entertainment system..
      		C


    		A.
    Go to step 14

    		B.
    GO TO AUDIO AND VISUAL SYSTEM (w/ Navigation System) (Click here)

    		C.
    GO TO REAR SEAT ENTERTAINMENT SYSTEM (Click here)

    11.CHECK HARD DISC

    1. Enter the "Failure Diagnosis" screen. Refer to Check Hard Disc in Operation Check (Click here).

      OK:
      "OK" is displayed.


    		NG.
    REPLACE HARD DISC (Click here)
    OK


    12.PROBLEM SYMPTOMS TABLE

    1. Refer to Problem Symptoms Table (Click here).

      Result
      Result
      		Proceed to
      Fault is not listed in Problem Symptoms Table.
      		A
      Fault is listed in Problem Symptoms Table.
      		B

      HINT:
      If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms (Click here).


    		B.
    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE
    A


    13.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

    1. Refer to Terminals of ECU (Click here).


    NEXT


    14.CHECK CIRCUIT

    1. Adjust, repair or replace as necessary.


    NEXT


    15.RECHECK FOR DIAGNOSTIC TROUBLE CODE*
      HINT:
      After clearing DTCs, recheck for DTCs (Click here).

    NEXT


    16.PERFORM CONFIRMATION TEST

      NEXT

      END