Audio And Visual System (W/ Multi-Display) Microphone Circuit Between Microphone And Radio Receiver

Audio Visual Telematics. Land Cruiser. Urj200, 202 Grj200 Vdj200
Audio Video. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

INSPECT MAP LIGHT ASSEMBLY

CHECK MAP LIGHT ASSEMBLY

CHECK TELEPHONE MICROPHONE ASSEMBLY

AUDIO AND VISUAL SYSTEM (w/ Multi-display) - Microphone Circuit between Microphone and Radio Receiver


DESCRIPTION

Using this circuit, the multi-media module receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly sends microphone signals to the multi-media module receiver assembly.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Audio Video.Audio And Visual System (For Radio Receiver Type).Audio And Visual System (W/ Multi-Display) Microphone Circuit Between Microphone And Radio Receiver


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the R7 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    F77-49 (SNS2) - R7-20 (SNS2)
    		Always
    		Below 1 Ω
    F77-29 (MACC) - R7-25 (ACC)
    		Always
    		Below 1 Ω
    F77-27 (MIN+) - R7-27 (MI1+)
    		Always
    		Below 1 Ω
    F77-48 (MIN-) - R7-26 (MIC-)
    		Always
    		Below 1 Ω
    F77-49 (SNS2) or R7-20 (SNS2) - Body ground
    		Always
    		10 kΩ or higher
    F77-29 (MACC) or R7-25 (ACC) - Body ground
    		Always
    		10 kΩ or higher
    F77-27 (MIN+) or R7-27 (MI1+) - Body ground
    		Always
    		10 kΩ or higher
    F77-48 (MIN-) or R7-26 (MIC-) - Body ground
    		Always
    		10 kΩ or higher
    F77-28 (SGND) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Audio Video.Audio And Visual System (For Radio Receiver Type).Audio And Visual System (W/ Multi-Display) Microphone Circuit Between Microphone And Radio Receiver

  1. Reconnect the multi-media module receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    F77-28 (SGND) - Body ground
    		Always
    		Below 1 Ω
    F77-48 (MIN-) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    F77-29 (MACC) - Body ground
    		Engine switch on (ACC)
    		4 to 6 V
Text in Illustration
*a
Component with harness connected
(Multi-media Module Receiver Assembly)


NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT MAP LIGHT ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Audio Video.Audio And Visual System (For Radio Receiver Type).Audio And Visual System (W/ Multi-Display) Microphone Circuit Between Microphone And Radio Receiver

  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    26 (MIC-) - 20 (SNS2)
    		Always
    		Below 1 Ω


NG
Go to step 5
OK


4.CHECK MAP LIGHT ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Audio Video.Audio And Visual System (For Radio Receiver Type).Audio And Visual System (W/ Multi-Display) Microphone Circuit Between Microphone And Radio Receiver

  1. Reconnect the multi-media module receiver assembly connector.

  1. Reconnect the map light assembly connector.

  1. Turn the engine switch on (ACC).

  1. Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Text in Illustration
    *a
    		Component with harness connected
    (Map Light Assembly)
    Result
    Result
    		Proceed to
    A waveform synchronized with the voice input to the map light assembly is not output.
    		A
    A waveform synchronized with the voice input to the map light assembly is output.
    		B


B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


5.CHECK TELEPHONE MICROPHONE ASSEMBLY

  1. Replace the telephone microphone assembly with a new or known good one (Click here).

  1. Check if the same malfunction recurs.

    OK:
    Malfunction does not recur (returns to normal).


NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)