Power Tilt And Power Telescopic Steering Column System Data List / Active Test

Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200
Steering Column. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. READ DATA LIST

  1. ACTIVE TEST

Power Tilt And Power Telescopic Steering Column System -- Data List / Active Test



READ DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

  6. According to the display on the GTS, read the Data List.

    Tilt & Telescopic
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Tilt Position
    		Current tilt position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Position
    		Current telescopic position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Return Position
    		Memorized tilt return position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Return Position
    		Memorized telescopic return position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Memory Pos 1
    		Tilt data of memory position 1/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Memory Pos 1
    		Telescopic data of memory position 1/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Memory Pos 2
    		Tilt data of memory position 2/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Memory Pos 2
    		Telescopic data of memory position 2/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Memory Pos 3
    		Tilt data of memory position 3/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Memory Pos 3
    		Telescopic data of memory position 3/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Up Limit
    		Uppermost tilt position/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Tilt Up Limit Position
    		Uppermost tilt position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Down Limit
    		Lowermost tilt position/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Tilt Down Limit Position
    		Lowermost tilt position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Short Limit
    		Shortest telescopic position/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Telesco Short Limit Pos
    		Shortest telescopic position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Telesco Long Limit
    		Longest telescopic position/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Telesco Long Limit Pos
    		Longest telescopic position data/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Tilt Up Switch
    		Input state of tilt up switch/
    ON or OFF
    		ON: Tilt up switch activated
    OFF: Tilt up switch not activated
    		-
    Tilt Up SW (CAN)
    		Input state of tilt up switch/
    ON or OFF
    		-
    		-
    Tilt Down Switch
    		Input state of tilt down switch/
    ON or OFF
    		ON: Tilt down switch activated
    OFF: Tilt down switch not activated
    		-
    Tilt Down SW (CAN)
    		Input state of tilt down switch/
    ON or OFF
    		-
    		-
    Telesco Short Switch
    		Input state of telescopic contract switch/
    ON or OFF
    		ON: Telescopic contract switch activated
    OFF: Telescopic contract switch not activated
    		-
    Telesco Short SW (CAN)
    		Input state of telescopic contract switch/
    ON or OFF
    		-
    		-
    Telesco Long Switch
    		Input state of telescopic extend switch/
    ON or OFF
    		ON: Telescopic extend switch activated
    OFF: Telescopic extend switch not activated
    		-
    Telesco Long SW (CAN)
    		Input state of telescopic extend switch/
    ON or OFF
    		-
    		-
    T&T Manual SW Data
    		Voltage data of tilt and telescopic switch/
    Min.: 0.00 V
    Max.: 4.99 V
    		Neutral position: Below 0.2 V
    Tilt up: 1.67 to 2.13 V
    Tilt down: 0.54 to 0.74 V
    Telescopic contract: 1.08 to 1.40 V
    Telescopic extend: 2.22 to 2.77 V
    		-
    S/B Mem 1
    		Tilt and telescopic memory position 1/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    S/B Mem 2
    		Tilt and telescopic memory position 2/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    S/B Mem 3
    		Tilt and telescopic memory position 3/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    T&T Autoaway Function
    		Auto away/return function/
    ON or OFF
    		ON: Auto away/return function allowed
    OFF: Auto away/return function prohibited
    		-
    Power Source Voltage
    		Voltage data of power supply/
    Min.: 0.00 V
    Max.: 19.99 V
    		11 to 14 V
    		-
    Freeze Speed Info
    		Vehicle speed data/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    		Actual vehicle speed
    		-
    IG Switch (CAN)
    		Communication state of engine switch/
    ON or OFF
    		ON: Communication normal
    OFF: Communication interrupted
    		-
    IG Switch
    		Input state of engine switch/
    ON or OFF
    		ON: Input signal normal
    OFF: Input signal interrupted
    		-
    Receive from Meter
    		Communication state of combination meter assembly signal/
    OK or Interpt
    		OK: Communication normal
    Interpt: Communication interrupted
    		-
    Receive from Seat ECU
    		Communication state of position control ECU signal/
    OK or Interpt
    		OK: Communication normal
    Interpt: Communication interrupted
    		-
    Receive from Combi
    		Communication state of combination switch ECU signal/
    OK or Interpt
    		-
    		-
    J/B
    		Communication state of main body ECU (multiplex network body ECU) signal/
    OK or Interpt
    		OK: Communication normal
    Interpt: Communication interrupted
    		-
    Driver Information 1
    		Driver information 1/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Driver 1 Tilt Mem
    		Driver tilt memory position 1/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Driver 1 Telesco Mem
    		Driver telescopic memory position 1/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Driver Information 2
    		Driver information 2/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Driver 2 Tilt Mem
    		Driver tilt memory position 2/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Driver 2 Telesco Mem
    		Driver telescopic memory position 2/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Driver Information 3
    		Driver information 3/
    Not Mem or Mem
    		Not Mem: No position memorized
    Mem: Position memorized
    		-
    Driver 3 Tilt Mem
    		Driver tilt memory position 3/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Driver 3 Telesco Mem
    		Driver telescopic memory position 3/
    Min.: 0
    Max.: 65535
    		28672 to 36864
    		-
    Handle Position
    		Steering wheel position signal/
    Away or Return
    		Away: Steering wheel in away position
    Return: Steering wheel in return position
    		-
    The Number of DTCs
    		Number of stored DTCs/
    Min.: 0
    Max.: 255
    		0
    		-


ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the engine switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

  6. According to the display on the GTS, perform the Active Test.

    Tilt & Telescopic
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Tilt Operation
    		Tilt operation
    		UP/DOWN
    		-
    Telesco Operation
    		Telescopic operation
    		LONG/SHORT
    		-