Steering. Land Cruiser. Urj200, 202 Grj200 Vdj200
Steering Column. Land Cruiser. Urj200, 202 Grj200 Vdj200
Power Tilt And Power Telescopic Steering Column System -- Data List / Active Test |
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
Check the values by referring to the table below.
Tilt & Telescopic Tester Display Measurement Item/Range Normal Condition Diagnostic Note Tilt Position Current tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Position Current telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Return Position Memorized tilt return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Return Position Memorized telescopic return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Memory Pos 1 Tilt data of memory position 1/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Memory Pos 1 Telescopic data of memory position 1/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Memory Pos 2 Tilt data of memory position 2/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Memory Pos 2 Telescopic data of memory position 2/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Memory Pos 3 Tilt data of memory position 3/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Memory Pos 3 Telescopic data of memory position 3/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Up Limit Uppermost tilt position/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- Tilt Up Limit Position Uppermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Down Limit Lowermost tilt position/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- Tilt Down Limit Position Lowermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Short Limit Shortest telescopic position/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- Telesco Short Limit Pos Shortest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Telesco Long Limit Longest telescopic position/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- Telesco Long Limit Pos Longest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)- Tilt Up Switch Input state of tilt up by manual switch/ON or OFF ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch- Tilt Up SW (CAN) Input state of tilt up by manual switch/ON or OFF ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch- Tilt Down Switch Input state of tilt down by manual switch/ON or OFF ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch- Tilt Down SW (CAN) Input state of tilt down by manual switch/ON or OFF ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch- Telesco Short Switch Input state of telescopic short by manual switch/ON or OFF ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch- Telesco Short SW (CAN) Input state of telescopic short by manual switch/ON or OFF ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch- Telesco Long Switch Input state of telescopic long by manual switch/ON or OFF ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch- Telesco Long SW (CAN) Input state of telescopic long by manual switch/ON or OFF ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch- T&T Manual SW Data Voltage data of manual switch/min.: 0 V, max.: 5 V Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V- S/B Mem 1 Tilt and telescopic memory position 1/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- S/B Mem 2 Tilt and telescopic memory position 2/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- S/B Mem 3 Tilt and telescopic memory position 3/Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized- T&T Autoaway Function Auto away/return function/ON or OFF ON: Auto away/return function allowed
OFF: Auto away/return function prohibited- Power Source Voltage Voltage data of power supply/min.: 0 V, max.: 20 V Actual power supply voltage
11 to 14 V- Freeze Speed Info Vehicle speed data/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed - IG Switch (CAN) Communication state of engine switch/ON or OFF ON: Communication normal
OFF: Communication interrupted- IG Switch Input state of engine switch/ON or OFF ON: Input signal normal
OFF: Input signal interrupted- Key Code Confirm (CAN) Communication state of key code confirmation signal/ON or OFF ON: Communication normal
OFF: Communication interrupted- Receive from Meter Communication state of combination meter signal/OK or Interruption OK: Communication normal
Interruption: Communication interrupted- Receive from Seat ECU Communication state of position control ECU signal/OK or Interruption OK: Communication normal
Interruption: Communication interrupted- Receive from Combi Communication state of combination switch ECU signal/OK or Interruption OK: Communication normal
Interruption: Communication interrupted- J/B Communication state of main body ECU signal/OK or Interruption OK: Communication normal
Interruption: Communication interrupted- B/B Communication state of optional after parts ECU signal/OK or Interruption OK: Communication normal
Interruption: Communication interrupted- Driver Seat Buckle SW Driver side buckle switch signal / Set, Unset or Unknown - - The Number of DTCs Number of diagnostic trouble codes/min.: 0, max.: 255 Actual number of diagnostic trouble codes -
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
Check the values by referring to the table below.
Tilt & Telescopic Tester Display Test Part Control Range Diagnostic Note Tilt Operation Tilt operation Up/Down - Telesco Operation Telescopic operation Long/Short -