Vane Pump (For 1Vd-Ftv With Dpf) Installation

Coat a new O-ring with power steering fluid and install it to the vane pump.

Install the vane pump with the 2 nuts.

Torque:

29 N*m{296 kgf*cm, 21 ft.*lbf}

Install a new gasket to the pressure feed tube.

Install the pressure feed tube and union with the union bolt.

Torque:

50 N*m{510 kgf*cm, 37 ft.*lbf}

HINT:

Make sure that the stopper of the tube touches the vane pump body as shown in the illustration before tightening the bolt.

Connect the 2 connectors.

Connect the pump hose to the vane pump with the clip.

Install the V-ribbed belt as shown in the illustration.

Temporarily install the lock nut, and turn the bolt clockwise.

Using a belt tension gauge, inspect the belt tension.

Standard Belt Tension:

Item	Condition	Specified Condition
New belt	5 to 35°C (41 to 95°F)	550 to 800 N (56 to 82 kgf, 123.6 to 179.8 lbf)
Used belt	5 to 35°C (41 to 95°F)	300 to 500 N (31 to 51 kgf, 67.4 to 112.4 lbf)

HINT:

1. When measuring the tension of a new belt, measure the tension immediately after installing it to the engine but before starting the engine.
   
2. A "new belt" is a belt which has been used for less than 5 minutes on a running engine.
   
3. A "used belt" is a belt which has been used on a running engine for 5 minutes or more.
   
4. After installing a new belt, run the engine for approximately 5 minutes and then recheck the tension.
   

Tighten the nut.

Torque:

40 N*m{408 kgf*cm, 30 ft.*lbf}

Check that the belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.

Align the No. 3 idler pulley bracket knock pin and No. 1 idler pulley bracket knock pin hole and install the No. 3 idler pulley with the nut.

Torque:

88 N*m{898 kgf*cm, 64 ft.*lbf}

Install the collar, No. 1 idler pulley and cover with the bolt.

Torque:

49 N*m{495 kgf*cm, 36 ft.*lbf}

Install the V-ribbed belt as shown in the illustration.

Temporarily install the lock nut, and turn the bolt clockwise.

Using a belt tension gauge, inspect the belt tension.

Standard Belt Tension:

Item	Condition	Specified Condition
New belt	5 to 35°C (41 to 95°F)	550 to 800 N (56 to 82 kgf, 123.6 to 179.8 lbf)
Used belt	5 to 35°C (41 to 95°F)	300 to 500 N (31 to 51 kgf, 67.4 to 112.4 lbf)

HINT:

1. When measuring the tension of a new belt, measure the tension immediately after installing it to the engine but before starting the engine.
   
2. A "new belt" is a belt which has been used for less than 5 minutes on a running engine.
   
3. A "used belt" is a belt which has been used on a running engine for 5 minutes or more.
   
4. After installing a new belt, run the engine for approximately 5 minutes and then recheck the tension.
   

Tighten the nut.

Torque:

40 N*m{408 kgf*cm, 30 ft.*lbf}

Check that the belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.

Install the radiator reservoir with the 3 bolts.

Connect the 2 hoses to the upper radiator tank and water inlet.

HINT:

Make sure the directions of the hose clamps are as shown in the illustration.

Connect the intake air connector to the No. 1 and No. 2 air cleaner pipes.

Install the connector with the 2 bolts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Tighten the 2 hose clamps.

Torque:

6.3 N*m{64 kgf*cm, 56 in.*lbf}

Attach the 3 wire harness clamps.

w/o Viscous Heater:
Connect the connector to the water temperature sensor.

w/ Viscous Heater:
Connect the 2 connectors to the water temperature sensor and viscous with magnet clutch heater.

Temporarily install the air cleaner hose to the intake air connector.

Connect the air cleaner cap to the air cleaner hose, and install the air cleaner cap with the 4 clamps.

Connect the mass air flow meter connector and attach the wire harness clamp to the air cleaner cap.

Attach the wire harness clamp.

Align the protrusion of the air cleaner cap and the concave portion of the air cleaner hose.

Tighten the 2 hose clamps.

Torque:

2.5 N*m{25 kgf*cm, 22 in.*lbf}

Install the engine cover with the 2 nuts.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Install the upper radiator support seal with the 7 clips.

Install the front fender apron seal front RH with the 3 clips.