Brake Pedal (For Lhd) -- Removal |
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 3. REMOVE FRONT DOOR SCUFF PLATE LH |
 |
Detach the 7 claws and 4 clips, and remove the front door scuff plate LH.
| 4. REMOVE COWL SIDE TRIM BOARD LH |
 |
Remove the cap nut.
Text in Illustration *a Cap Nut
Detach the 2 clips and remove the cowl side trim board LH.
| 5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
 |
Remove the 2 screws <A>.
Text in Illustration *a Screw <A>
Detach the 3 claws.
Disconnect the connector and remove the No. 1 instrument panel under cover sub-assembly.
| 6. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
 |
Using a screwdriver, detach the 2 claws and open the hole cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *a Protective Tape
Put protective tape around the lower No. 1 instrument panel finish panel.
 |
Remove the 2 bolts <B>.
Text in Illustration *a Protective Tape *b Bolt <B>
w/ Driver Side Knee Airbag:
Detach the 16 claws.
w/o Driver Side Knee Airbag:
Detach the 9 claws.
for Automatic Air Conditioning System:
Detach the 2 claws and remove the room temperature sensor.
Detach the 2 claws and disconnect the 2 control cables.
 |
Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.
| 7. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Remove the 5 bolts and driver side knee airbag assembly.
 |
Using a screwdriver, release the connector lock and disconnect the airbag connector.
Text in Illustration *a Connector Lock 
Protective Tape - NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
| 8. REMOVE NO. 2 CONNECTOR HOLDER |
Loosen the bolt and disconnect the connector from the No. 2 connector holder.
Text in Illustration 
Remove in this Direction
 |
Disconnect the wire harness clamp from the brake pedal support assembly.
 |
Detach the two claws (A) of the No. 2 connector holder.
Text in Illustration Pull Towards You
Unlock the claw (B), and then pull the No. 2 connector holder towards you to remove it.
| 9. REMOVE PUSH ROD PIN |
Remove the clip and push rod pin from the brake pedal lever.
Text in Illustration *A for Automatic Transmission *B for Manual Transmission
 |
| 10. REMOVE STOP LIGHT SWITCH ASSEMBLY |
Disconnect the stop light switch connector.
Remove the stop light switch (Click here).
| 11. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY |
Loosen the hexagon bolt.
Text in Illustration *A for Automatic Transmission *B for Manual Transmission - HINT:
- Hold the bolt in place and loosen the nut.
- NOTICE:
- Only loosen the nut. Do not remove the bolt or nut.
 |
Remove the brake pedal support reinforcement set bolt.
Remove the 4 nuts and brake pedal support assembly.
Text in Illustration *A for Automatic Transmission *B for Manual Transmission
 |