Tire Pressure Warning System Diagnosis System

Suspension. Land Cruiser. Urj200, 202 Grj200 Vdj200
Tire Pressure Monitoring. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. CHECK WARNING LIGHT

  1. WHAT TO CONSIDER WHEN TIRE PRESSURE WARNING LIGHT ILLUMINATES

  1. TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

  1. NORMAL MODE DTC

  1. TEST MODE (SIGNAL CHECK MODE) DTC

Tire Pressure Warning System -- Diagnosis System



CHECK WARNING LIGHT
NOTICE:
  1. When there is a problem with the tire pressure warning system, the tire pressure warning light blinks at 0.5 second intervals, and illuminates after 1 minute.
  2. When the malfunction has been corrected, the tire pressure warning light goes off.
  3. When the tire pressure warning light illuminates, immediately check the tire pressure of the tires and adjust them to the specified value.
  4. After the engine switch is turned on (IG), the tire pressure warning light illuminates for 3 seconds and then goes off. If the warning light does not illuminate for 3 seconds, proceed to the troubleshooting for the tire pressure warning light circuit (Click here).


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System

  1. Turn the engine switch on (IG).

    Text in Illustration
    *1
    		Tire Pressure Warning Light

  2. Check that the tire pressure warning light illuminates for 3 seconds.


WHAT TO CONSIDER WHEN TIRE PRESSURE WARNING LIGHT ILLUMINATES

  1. When the tire pressure warning light does not go off, or when it illuminates during driving, check the tire pressure. If the tire pressure warning light illuminates within several hours after adjusting the tire pressure, a tire may have a slow air leak.

  2. The system is disabled under the following conditions (when the condition returns to normal, the system will work properly).

    1. When all of the tire and wheel assemblies that have tire pressure warning valve and transmitters registered with the tire pressure warning ECU and receiver have not been installed.

    2. When all of the transmitter ID codes are not registered with the tire pressure warning ECU and receiver.

    3. When the tire pressure is abnormally high (absolute pressure: 480 kPa (4.9 kgf/cm2, 70 psi) or more; relative pressure: 380 kPa (3.9 kgf/cm2, 55 psi) or more).

    4. When a tire pressure warning valve and transmitter battery is depleted.

  3. The system may be disabled under the following conditions (when the condition returns to normal, the system will work properly).

    1. When electric devices or facilities using similar radio frequencies are nearby.

    2. When a wireless device or other equipment operating at a similar frequency is in use in the vehicle.

    3. When a window tint that affects radio wave signals is installed.

    4. When there is a lot of snow or ice on the vehicle, in particular, around the wheels or wheel housing.

    5. When non-genuine wheels are used.

    6. When tire chains are used.

    7. When aftermarket tire repair sealant is used.

      CAUTION:
      After use of tire repair sealant, replacement of the tire pressure warning valve and transmitter is required to ensure normal system operation. (Normal system operation cannot be ensured by only repairing or replacing the tire.)

TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

HINT:
The table below indicates the state of the tire pressure warning light after the engine switch is turned on (IG).


Immediately after turning the engine switch on (IG)
Always
Warning light output pattern
Illuminates for 3 sec.
Goes off
Illuminates
Blinks
Outputs DTC
Normal
○
○
-
-
-
Low tire pressure
○
-
○
-
-
System failure
○
-
-
*1
-
Test mode (signal check mode)
○
-
-
*2
-
Initialization
○
-
-
*3
-
Tire position identification in progress
○
○
-
-
-
ECU connector poorly connected
-
-
-
*4
-
TC grounded (DTCs are output)
○
-
-
-
○
TC grounded (DTCs are not output)
○
-
-
*5
-

  1. Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System
    *1: Blinks at 0.5 second intervals, and remains illuminated after 1 minute.
    Text in Illustration
    *a
    		ON
    *b
    		OFF
    *c
    		0.5 sec.
    *d
    		1 minute

  2. Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System
    *2: Blinks at 0.125 second intervals.
    Text in Illustration
    *a
    		ON
    *b
    		OFF
    *c
    		0.125 sec.

  3. Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System
    *3: Blinks 3 times at 1 second intervals.
    Text in Illustration
    *a
    		ON
    *b
    		OFF
    *c
    		1 sec.

  4. Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System
    *4: Goes off for 10 seconds to check the connection of the ECU connector, and then blinks at 0.5 second intervals, and remains illuminated after 1 minute.
    Text in Illustration
    *a
    		ON
    *b
    		OFF
    *c
    		0.5 sec.
    *d
    		1 minute
    *e
    		10 sec.

  5. Land Cruiser. Urj200, 202 Grj200 Vdj200.Tire Pressure Monitoring.Tire Pressure Warning System.Tire Pressure Warning System Diagnosis System
    *5: Blinks at 0.25 second intervals.
    Text in Illustration
    *a
    		ON
    *b
    		OFF
    *c
    		0.25 sec.

NORMAL MODE DTC

  1. DTCs are stored in the tire pressure warning ECU and receiver and output by blinking the tire pressure warning light or by using the GTS (Click here).


TEST MODE (SIGNAL CHECK MODE) DTC

  1. By switching from normal mode into test mode (signal check mode), the tire pressure warning ECU and receiver, each tire pressure warning valve and transmitter and tire pressure warning reset switch can be inspected (Click here).