Rear Upper Arm Removal

Suspension. Land Cruiser. Urj200, 202 Grj200 Vdj200
Rear Suspension. Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. REMOVE STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)

  2. OPEN STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)

  3. REMOVE REAR WHEEL

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Active Height Control)

  5. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Active Height Control)

  6. DISCONNECT SPEED SENSOR WIRE HARNESS

  7. REMOVE REAR STABILIZER CONTROL TUBE INSULATOR (w/ KDSS)

  8. REMOVE UPPER ARM BUSH HEAT INSULATOR (w/o KDSS)

  9. SUPPORT REAR AXLE HOUSING ASSEMBLY

  10. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH (w/ Active Height Control)

  11. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH (w/o Active Height Control)

Rear Upper Arm -- Removal


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. REMOVE STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Detach the clamp, and disconnect the connector from the protector.

  1. Remove the 3 bolts and protector.



2. OPEN STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)


  1. Using a 5 mm hexagon socket wrench, loosen the lower and upper chamber shutter valves of the stabilizer control with accumulator housing 2.0 to 3.5 turns.


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Rear Suspension.Rear Suspension System.Rear Upper Arm Removal

    NOTICE:
    1. When loosening a shutter valve, make sure that the end protrudes 2 to 3.5 mm (0.0787 to 0.137 in.) from the surface of the block, and do not turn the shutter valve any further.
    2. Do not remove the shutter valves.


3. REMOVE REAR WHEEL


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Active Height Control)


5. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Active Height Control)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Disconnect the connector and 2 clamps.



    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts, nut and sensor.



6. DISCONNECT SPEED SENSOR WIRE HARNESS


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the bolt and disconnect the speed sensor wire harness from the upper control arm.



7. REMOVE REAR STABILIZER CONTROL TUBE INSULATOR (w/ KDSS)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 bolts and rear stabilizer control tube insulator.



8. REMOVE UPPER ARM BUSH HEAT INSULATOR (w/o KDSS)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the bolt and upper arm bush heat insulator.



9. SUPPORT REAR AXLE HOUSING ASSEMBLY


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Support the rear axle housing with a jack using a wooden block to avoid damage.



10. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH (w/ Active Height Control)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 nuts, 2 washers, 2 bolts and upper control arm.



11. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH (w/o Active Height Control)


    Land Cruiser. Urj200, 202 Grj200 Vdj200

  1. Remove the 2 nuts, 2 washers, 2 bolts and upper control arm.