Dtc P0500 Vehicle Speed Sensor

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ae80F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF SPEEDOMETER

READ VALUE USING GTS (VEHICLE SPEED)

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)

CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)

DTC P0500 Vehicle Speed Sensor


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0500
  1. Transmission revolution sensor (SP2) value is 9 km/h (5.59 mph) or more
  2. Vehicle speed signal is not input
  3. 5 seconds or more
  4. 2-trip detection logic
  1. Open or short in vehicle speed signal circuit
  2. Combination meter system
  3. Skid control ECU (master cylinder solenoid)
  4. TCM

MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.59 mph). If there is no speed signal from the combination meter despite this condition being met, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0500 Vehicle Speed Sensor


INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).
HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the engine switch on (IG) and wait for 3 seconds or more.*1
  2. Drive the vehicle at 9 km/h (5.59 mph) or more for 5 seconds or more.*2
  3. Turn the engine switch off.
  4. Perform steps (*1) through (*2) again.
  5. Check for DTCs again (Click here).
1.CHECK OPERATION OF SPEEDOMETER

  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).


NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING GTS (VEHICLE SPEED)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. In accordance with the display on the GTS, read the Data List.

    ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Vehicle Speed
    		Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    		Actual vehicle speed
    		-
    OK:
    Vehicle speed displayed on GTS and speedometer display are equal.


NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

  1. Disconnect the E119 combination meter assembly connector.

  1. Disconnect the A82 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    E119-6 (+S) - A82-18 (SPD)
    		Always
    		Below 1 Ω
    E119-6 (+S) or A82-18 (SPD) - Body ground
    		Always
    		10 kΩ or higher
    HINT:
    If the wire harness has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. SFI system, audio system, etc.).


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEMS RELATED TO SPEED SIGNAL)
OK


4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0500 Vehicle Speed Sensor

  1. Disconnect the combination meter connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-6 (+S) - Body ground
    		Engine switch on (IG)
    		4.5 to 5.5 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Combination Meter Assembly)


NG
REPLACE TCM (Click here)
OK


5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0500 Vehicle Speed Sensor

  1. Remove the combination meter.

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-6 (+S) - Body ground
    		Engine switch on (IG)
    (Turn wheel slowly)
    		Voltage generated intermittently
    Text in Illustration
    *a
    		Component with harness connected
    (Combination Meter Assembly)
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


NG
Go to step 6
OK

REPLACE TCM (Click here)

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ae80F Automatic Transmission Transaxle.Automatic Transmission System. Dtc P0500 Vehicle Speed Sensor

  1. Remove the combination meter.

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the engine switch on (IG).

  1. Check the voltage between the body ground while the wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-5 (SI) - Body ground
    		Engine switch on (IG)
    (Turn wheel slowly)
    		Voltage generated intermittently
    Text in Illustration
    *a
    		Component with harness connected
    (Combination Meter Assembly)
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


NG
Go to step 7
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)

  1. Disconnect the E119 combination meter connector.

  1. Disconnect the A24 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    E119-5 (SI) - A24-12 (SP1)
    		Always
    		Below 1 Ω
    E119-5 (SI) or A24-12 (SP1) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID) (Click here)