Dtc P0982 Shift Solenoid D Control Circuit Low (Shift Solenoid Valve S4)

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)

CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

INSPECT SHIFT SOLENOID VALVE S4

DTC P0982 Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)

DTC P0983 Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)


DESCRIPTION

Shifting from 1st to 6th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending current to the open or short circuited solenoid (Click here).

DTC Code
DTC Detection Condition
Trouble Area
P0982
The ECM detects a short in the solenoid valve S4 circuit 2 times when the solenoid valve S4 is operated (1 trip detection logic).
  1. Short in shift solenoid valve S4 circuit
  2. Shift solenoid valve S4
  3. ECM
P0983
The ECM detects an open in the solenoid valve S4 circuit 2 times when the solenoid valve S4 is not operated (1 trip detection logic).
  1. Open in shift solenoid valve S4 circuit
  2. Shift solenoid valve S4
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S4 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S4 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S4 circuit.
When the shift solenoid valve S4 is OFF, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S4 circuit (Click here).

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0982 Shift Solenoid D Control Circuit Low (Shift Solenoid Valve S4)


INSPECTION PROCEDURE


HINT:
The shift solenoid valve S4 is turned ON/OFF normally when the shift lever is in D:

ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve S4
OFF
OFF
OFF
OFF
ON
ON
1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0982 Shift Solenoid D Control Circuit Low (Shift Solenoid Valve S4)

  1. Disconnect the No. 1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    14 (S4) - Body ground
    		20°C (68°F)
    		11 to 15 Ω
    Text in Illustration
    *a
    		Component without harness connected
    (No. 1 Transmission Wire)


NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0982 Shift Solenoid D Control Circuit Low (Shift Solenoid Valve S4)

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    C45-6 (S4) - Body ground
    		20°C (68°F)
    		11 to 15 Ω
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    C46-6 (S4) - Body ground
    		20°C (68°F)
    		11 to 15 Ω
Text in Illustration
*1
for LHD
*2
for RHD
*a
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3.INSPECT SHIFT SOLENOID VALVE S4


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0982 Shift Solenoid D Control Circuit Low (Shift Solenoid Valve S4)

  1. Remove the shift solenoid valve S4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body
    		20°C (68°F)
    		11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    		Specified Condition
    1. Battery positive (+) → Shift solenoid valve S4 connector
    2. Battery negative (-) → Shift solenoid valve S4 body
    		Valve moves and makes an operating noise
Text in Illustration
*a
Component without harness connected
(Shift Solenoid Valve S4)


NG
REPLACE SHIFT SOLENOID VALVE S4 (Click here)
OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (Click here)