Dtc P0724 Brake Switch B Circuit High

Drivetrain. Land Cruiser. Urj200, 202 Grj200 Vdj200
Ab60F Automatic Transmission Transaxle. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT STOP LIGHT SWITCH

CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

DTC P0724 Brake Switch "B" Circuit High


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains on even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) pattern 5 times (2 trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during "stop and go" driving, the ECM interprets this as a fault in the stop light switch, the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) five times for 2 driving cycles in order to detect a malfunction.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0724 Brake Switch B Circuit High


INSPECTION PROCEDURE


DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Stop Light Switch
    		Stop light switch status/
    ON or OFF
    		Brake pedal:
    1. Depressed: ON
    2. Released: OFF
    		-
1.INSPECT STOP LIGHT SWITCH


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0724 Brake Switch B Circuit High

  1. Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 - 2
    		Pin not pushed
    		Below 1 Ω
    3 - 4
    		Pin pushed
    		Below 1 Ω
    1 - 2
    		Pin pushed
    		10 kΩ or higher
    3 - 4
    		Pin not pushed
    		10 kΩ or higher


NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)


    Land Cruiser. Urj200, 202 Grj200 Vdj200.Ab60F Automatic Transmission Transaxle.Automatic Transmission System (For 1Ur-Fe). Dtc P0724 Brake Switch B Circuit High

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD
    Tester Connection
    		Condition
    		Specified Condition
    A38-36 (STP) - Body ground
    		Brake pedal depressed
    		11 to 14 V
    A38-36 (STP) - Body ground
    		Brake pedal released
    		Below 1 V
    for RHD
    Tester Connection
    		Condition
    		Specified Condition
    A52-36 (STP) - Body ground
    		Brake pedal depressed
    		11 to 14 V
    A52-36 (STP) - Body ground
    		Brake pedal released
    		Below 1 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)