Dtc C1A47 Steering Angle Sensor

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
Cruise Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

INSPECTION PROCEDURE

CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)

CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

REPLACE FORWARD RECOGNITION CAMERA

CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

DTC C1A47 Steering Angle Sensor


DESCRIPTION

The forward recognition camera receives steering angle information from the steering angle sensor (spiral cable sub-assembly). If the forward recognition camera detects a steering angle sensor malfunction, DTC C1A47 is stored.

DTC No.
DTC Detection Condition
Trouble Area
C1A47
2 seconds after the engine switch is turned on (IG), a signal from the steering angle sensor indicating that there is a steering angle sensor malfunction is detected by the forward recognition camera for 5 seconds or more.
  1. Vehicle stability control system
  2. Steering angle sensor
  3. Forward recognition camera

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
  2. If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (Click here).
  3. First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (Click here).
1.CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

  1. Check for DTCs (Click here).

Result
Result
Proceed to
Vehicle stability control system DTCs are not output
A
Vehicle stability control system DTCs are output
B
HINT:
If the steering angle sensor is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.


B
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

  1. Clear the DTCs (Click here).

  1. Make sure that the DTC detection conditions are met.

    HINT:
    If the following procedure is not performed, the previously output DTC cannot be detected.
    1. Turn the engine switch on (IG) and wait 7 seconds or more.

  1. Check for DTCs (Click here).

Result
Result
Proceed to
DTC C1A47 is output
A
DTC C1A47 is not output
B


B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.REPLACE FORWARD RECOGNITION CAMERA

  1. Replace the forward recognition camera (Click here).

  1. Adjust the forward recognition camera (Click here).


NEXT


4.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

  1. Clear the DTCs (Click here).

  1. Make sure that the DTC detection conditions are met.

    HINT:
    If the following procedure is not performed, the previously output DTC cannot be detected.
    1. Turn the engine switch on (IG) and wait 7 seconds or more.

  1. Check for DTCs (Click here).

Result
Result
Proceed to
DTC C1A47 is output
A
DTC C1A47 is not output
B


B
END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
A

REPLACE STEERING ANGLE SENSOR (Click here)