Dtc P0500 Vehicle Speed Sensor A

Engine Hybrid System. Land Cruiser. Urj200, 202 Grj200 Vdj200
3Ur-Fe Engine Control. Land Cruiser. Urj200, 202 Grj200 Vdj200

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF SPEEDOMETER

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)

CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)

CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

DTC P0500 Vehicle Speed Sensor "A"


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

Land Cruiser. Urj200, 202 Grj200 Vdj200.3Ur-Fe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A


DTC Code
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM

MONITOR DESCRIPTION


  1. The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM


Land Cruiser. Urj200, 202 Grj200 Vdj200.3Ur-Fe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK OPERATION OF SPEEDOMETER

  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).


NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.


NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

  1. Disconnect the E119 combination meter connector.

  1. Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    E119-6 (+S) - A38-44 (SPD)
    		Always
    		Below 1 Ω
    E119-6 (+S) or A38-44 (SPD) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
Land Cruiser. Urj200, 202 Grj200 Vdj200.3Ur-Fe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A

  1. Disconnect the E119 combination meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-6 (+S) - Body ground
    		Engine switch on (IG)
    		4.5 to 5.5 V


NG
REPLACE ECM (Click here)
OK


5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.3Ur-Fe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-6 (+S) - Body ground
    1. Engine switch on (IG)
    2. Wheel turned slowly
    		Voltage generated intermittently
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


NG
CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
OK


6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
Land Cruiser. Urj200, 202 Grj200 Vdj200.3Ur-Fe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E119-5 (SI) - Body ground
    1. Engine switch on (IG)
    2. Wheel turned slowly
    		Voltage generated intermittently
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


NG
Go to step 7
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

  1. Disconnect the combination meter connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):

Tester Connection
Condition
Specified Condition
E119-5 (SI) - A24-12 (SP1)
Always
Below 1 Ω

Standard Resistance (Check for Short):

Tester Connection
Condition
Specified Condition
E119-5 (SI) or A24-12 (SP1) - Body ground
Always
10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID