Система Ecd Pre-Heating Control Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK GLOW INDICATOR LIGHT

CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

CHECK INDICATOR LIGHTING TIME AND AFTER GLOW TIME

READ OUTPUT DTC

INSPECT GLOW RELAY ASSEMBLY

CHECK ECM (SREL VOLTAGE)

CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)

CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY (GLOW) - GLOW PLUG ASSEMBLY AND BATTERY)

CHECK ECM (GIND VOLTAGE)

CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

ПРИМЕЧАНИЕ:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1. Turn the ignition switch to ON.
   

2. Check that the glow indicator light comes on.
   

   OK:

   The glow indicator light remains on for 0.5 seconds or more, and then goes off.
   

1. Check that the glow plug assembly and glow plug wire are securely installed.
   

   OK:

   The glow plug assembly and glow plug wire are securely installed.
   

1. Inspect the glow plug assembly (See page Нажмите здесь).
   

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / DTC.
   

4. Read the DTCs (See page Нажмите здесь).
   

   Result

   Result	Proceed to
   DTC is not output	A
   DTC is output	B

1. Inspect the glow plug relay (GLOW) (See page Нажмите здесь).
   

1. Turn the ignition switch to the start position.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Condition	Specified Condition
   G61-2 (SREL) - C101-14 (E1)	Cranking	11 to 14 V

   Text in Illustration

   *a	Component with harness connected (ECM)

1. Disconnect the ECM connector.
   

2. Remove the glow relay from the engine room relay block.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance (Check for Open):

   Tester Connection	Condition	Specified Condition
   G61-2 (SREL) - Relay block glow relay terminal 2	Always	Below 1 Ω
   Relay block glow relay terminal 1 - Body ground	Always	Below 1 Ω

   Standard Resistance (Check for Short):

   Tester Connection	Condition	Specified Condition
   G61-2 (SREL) or relay block glow relay terminal 2 - Body ground	Always	10 kΩ or higher

4. Reconnect the ECM connector.
   

5. Reinstall the glow relay.
   

1. Disconnect the cable from the negative (-) battery terminal.
   

2. Disconnect the cable from the positive (+) battery terminal.
   

3. Remove the glow relay from the engine room relay block.
   

4. Disconnect the glow plug wire.
   

5. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance (Check for Open):

   Tester Connection	Condition	Specified Condition
   Relay block glow relay terminal 3 - C114-1	Always	Below 1 Ω
   Relay block glow relay terminal 5 - Positive (+) battery terminal	Always	Below 1 Ω

   ПРИМЕЧАНИЕ:

   After reconnecting the battery cable, the radio and clock need to be adjusted as they were previously.

6. Reinstall the glow relay.
   

7. Reconnect the glow plug wire.
   

8. Reconnect the cable to the positive (+) battery terminal.
   

9. Reconnect the cable to the negative (-) battery terminal.
   

1. Disconnect the ECM connector.
   

2. Turn the ignition switch to ON.
   

3. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   G62-1 (GIND) - C101-14 (E1)	Ignition switch ON	11 to 14 V

   Text in Illustration

   *a	Rear view of wire harness connector (to ECM)

4. Reconnect the ECM connector.
   

1. Disconnect the combination meter assembly connector.
   

2. Disconnect the ECM connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   G7-8 - G62-1 (GIND)	Always	Below 1 Ω

4. Reconnect the combination meter assembly connector.
   

5. Reconnect the ECM connector.
   

1. Disconnect the combination meter assembly connector.
   

2. Turn the ignition switch to ON.
   

3. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   G6-28 - Body ground	Ignition switch ON	11 to 14 V

   Text in Illustration

   *a	Front view of wire harness connector (to Combination Meter Assembly)

4. Reconnect the combination meter assembly connector.