Transfer System Precaution

Drivetrain. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
Vf2A Transfer 4Wd Awd. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

  1. Before disassembling the transfer assembly, thoroughly clean it to remove any foreign matter. This will help prevent contamination during disassembly and reassembly.

  1. When removing the transfer cover or any other light alloy parts, do not pry them off with a screwdriver or other tool that may cause damage. Instead, tap the parts with a plastic-faced hammer.

  1. Always arrange removed parts in the order they were removed and protect them from foreign matter.

  1. Before installation of each part, thoroughly clean and dry it. Then apply transfer oil to it. Do not use alkaline chemicals to clean aluminum parts, rubber parts or ring gear set bolts. Also, do not use non-residue solvent or other cleaning oils to clean O-rings, oil seals or rubber parts.

  1. Coat sliding surfaces and rotating parts with hypoid gear oil.

  1. Do not directly fix a part in a vise. Place aluminum plates between the part and vise.

  1. Replace any damaged or deformed snap rings with new ones.

  1. Do not allow the case mating surfaces to be scratched. Scratches may lead to oil leakage.

  1. Using a razor blade and gasket scraper, remove old seal packing from the sealing surface.

  1. Clean all parts to remove excess seal packing completely.

  1. Clean the sealing surface with solvent so that no residue remains on the sealing surface.

  1. Apply seal packing in a continuous line of approximately 1.2 mm (0.0472 in.) in diameter along the sealing surface.

  1. Be sure to assemble parts within 10 minutes of seal packing application. Otherwise, the seal packing must be removed and reapplied.

  1. After sealing parts, do not allow oil to come into contact with the seal for at least 1 hour.

  1. Do not allow scratches on surfaces which contact oil seals or gaskets. Scratches may lead to oil leakage.

  1. When press-fitting an oil seal, be careful not to damage the lip of the oil seal and its periphery.

Transfer System -- Precaution



1.Before disassembling the transfer assembly, thoroughly clean it to remove any foreign matter. This will help prevent contamination during disassembly and reassembly.

2.When removing the transfer cover or any other light alloy parts, do not pry them off with a screwdriver or other tool that may cause damage. Instead, tap the parts with a plastic-faced hammer.

3.Always arrange removed parts in the order they were removed and protect them from foreign matter.

4.Before installation of each part, thoroughly clean and dry it. Then apply transfer oil to it. Do not use alkaline chemicals to clean aluminum parts, rubber parts or ring gear set bolts. Also, do not use non-residue solvent or other cleaning oils to clean O-rings, oil seals or rubber parts.

5.Coat sliding surfaces and rotating parts with hypoid gear oil.

6.Do not directly fix a part in a vise. Place aluminum plates between the part and vise.

7.Replace any damaged or deformed snap rings with new ones.

8.Do not allow the case mating surfaces to be scratched. Scratches may lead to oil leakage.

9.Using a razor blade and gasket scraper, remove old seal packing from the sealing surface.

10.Clean all parts to remove excess seal packing completely.

11.Clean the sealing surface with solvent so that no residue remains on the sealing surface.

12.Apply seal packing in a continuous line of approximately 1.2 mm (0.0472 in.) in diameter along the sealing surface.

13.Be sure to assemble parts within 10 minutes of seal packing application. Otherwise, the seal packing must be removed and reapplied.

14.After sealing parts, do not allow oil to come into contact with the seal for at least 1 hour.

15.Do not allow scratches on surfaces which contact oil seals or gaskets. Scratches may lead to oil leakage.

16.When press-fitting an oil seal, be careful not to damage the lip of the oil seal and its periphery.