Manual Transmission Assembly -- Removal |
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (HILUX_TGN26 RM000004QR1003X.html)
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3003X.html).
| 3. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box) |
| 4. REMOVE SHIFT LEVER BOOT ASSEMBLY |
w/o Console Box:
Remove the front seat, front door scuff plate, etc. and fold back the floor carpet so that the shift lever can be removed.
Remove the 4 screws, 2 clips and shift lever boot assembly.
Text in Illustration *1 Screw *2 Clip
 |
| 5. REMOVE FLOOR SHIFT LEVER ASSEMBLY |
Cover the shift lever cap with a cloth.
Text in Illustration *1 Cloth *a Press down *b Rotate counterclockwise
 |
Press down on the shift lever cap and rotate it counterclockwise to remove it.
Pull out the shift lever.
| 6. REMOVE NO. 1 ENGINE UNDER COVER |
| 7. REMOVE NO. 2 ENGINE UNDER COVER |
| 8. DRAIN MANUAL TRANSMISSION OIL |
Remove the filler plug and gasket.
Remove the drain plug and gasket to drain the manual transmission oil.
Install a new gasket and the drain plug.
- Torque:
- 37 N*m{377 kgf*cm, 27 ft.*lbf}
| 9. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
| 10. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
for 2TR-FBE: (HILUX_TGN26 RM00000135901GX.html)
for 1KD-FTV: (HILUX_TGN26 RM00000121301DX.html)
for 2KD-FTV: (HILUX_TGN26 RM00000121301EX.html)
| 11. DISCONNECT WIRE HARNESS |
Disconnect the back-up light switch connector and speedometer sensor connector.
| 12. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY |
Remove the 2 bolts and disconnect the release cylinder assembly.
 |
| 13. REMOVE STARTER ASSEMBLY |
for 2TR-FBE: (HILUX_TGN26 RM000000SH200VX.html)
for 1KD-FTV: (HILUX_TGN26 RM0000013XL02NX.html)
for 2KD-FTV DENSO made: (HILUX_TGN26 RM0000013XL02MX.html)
for 2KD-FTV BOSCH made: (HILUX_TGN26 RM0000013XL02OX.html)
| 14. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
Support the transmission rear side with a support stand.
Remove the 4 set bolts of the rear No. 1 engine mounting insulator.
 |
Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly.
 |
| 15. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
Remove the 4 bolts and mounting insulator.
 |
| 16. REMOVE MANIFOLD STAY (for TR Series Engine) |
Remove the 3 bolts and manifold stay.
 |
| 17. REMOVE STIFFENER PLATE (for 1KD-FTV, 2KD-FTV) |
Remove the 4 bolts and stiffener plate RH.
 |
Remove the 4 bolts and stiffener plate LH.
| 18. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY |
Using a transmission jack, support the transmission.
Remove the support stand from the transmission.
for 1KD-FTV, 2KD-FTV:
Remove the 5 bolts and transmission.Text in Illustration *A for TR Engine series *B for 1KD-FTV, 2KD-FTV
 |
for TR Engine series:
Remove the 7 bolts and transmission.