Dtc P0500 Vehicle Speed Sensor A

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
2Tr-Fbe Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

CHECK COMBINATION METER SYSTEM

CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)

CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)

DTC P0500 Vehicle Speed Sensor "A"


DESCRIPTION

The vehicle speed sensor outputs 4 pulses for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of this pulse signal.

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fbe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A


for Automatic Transmission
DTC No.
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, no vehicle speed sensor signal is sent to the ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Combination meter
  3. Speed Sensor
  4. ECM

for Manual Transmission
DTC No.
DTC Detection Condition
Trouble Area
P0500
Conditions (a), (b) and (c) are met for 2000 seconds or more (2 trip detection logic):
  1. (a) Vehicle is being driven.
  2. (b) Fuel-cut operation is being performed.
  3. (c) No speed signal is sent to the ECM.
  1. Open or short in speed signal circuit
  2. Combination meter
  3. Speed Sensor
  4. ECM

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fbe Engine Control.Sfi System. Dtc P0500 Vehicle Speed Sensor A


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the intelligent tester.

    OK:
    Vehicle speeds displayed on intelligent tester and speedometer display are equal.


NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (HILUX_TGN26 RM000000PDQ0YMX.html)

2.CHECK COMBINATION METER SYSTEM

  1. Inspect the circuits that send vehicle speed signals to this system in the meter system (HILUX_TGN26 RM000002UD709OX.html).

  1. During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


NEXT


3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)

  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    G19-6 (+S) - G146-16 (SPD)
    		Always
    		Below 1 Ω


NG
Go to step 4
OK

REPLACE ECM (HILUX_TGN26 RM000000VW2024X.html)

4.CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)

  1. Disconnect the ECM connector.

  1. Disconnect the junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    2P-26 - G146-16 (SPD)
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR IS DEFECTIVE)