Dtc P0500 Vehicle Speed Sensor A

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
2Kd-Ftv Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK OPERATION OF SPEEDOMETER

READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

CHECK HARNESS AND CONNECTOR

CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

REPLACE ECM

CHECK SPEEDOMETER CIRCUIT

REPLACE COMBINATION METER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P0500 Vehicle Speed Sensor "A"


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P0500 Vehicle Speed Sensor A


P0500
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive the vehicle at 10 km/h (6.3 mph) or more
Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 19 mm3/st or more.
(c) No speed signal is input to the ECM.
  1. Open or short in speedometer circuit
  2. Speedometer assembly
  3. ECM
Drive the vehicle at 10 km/h (6.3 mph) or more
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.

Related Data List
DTC No.
Data List
P0500
Vehicle Speed

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P0500 Vehicle Speed Sensor A


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK070X.html) and initialization (HILUX_TGN26 RM000000TIN057X.html).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (HILUX_TGN26 RM000000TIN057X.html).
  4. After replacing an injector assembly, the ECM needs registration (HILUX_TGN26 RM0000012XK070X.html).
HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.CHECK OPERATION OF SPEEDOMETER

  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

    HINT:
    The vehicle speed sensor is operating normally if the speedometer reading is normal.
    OK:
    The vehicle speed sensor is operating normally.


NG
Go to step 7
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speed displayed on tester and speedometer display are equal.


OK
Go to step 10

NG
Go to step 3

3.CHECK HARNESS AND CONNECTOR
Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P0500 Vehicle Speed Sensor A

  1. Disconnect the combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G19-6 (+S) - Body ground
    		Ignition switch ON
    		4.5 to 5.5 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Combination Meter Assembly)

  1. Reconnect the combination meter assembly connector.



NG
Go to step 5
OK


4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Kd-Ftv Engine Control.Ecd System (For Dpf). Dtc P0500 Vehicle Speed Sensor A

  1. Move the shift lever to neutral.

  1. Jack up the vehicle.

  1. Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G19-6 (+S) - Body ground
    		Ignition switch ON
    		Voltage generated intermittently
    Text in Illustration
    *a
    		Component with harness connected
    (Combination Meter Assembly)
    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


OK
Go to step 6

NG
Go to step 8

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

  1. Disconnect the combination meter assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    G19-6 (+S) - G148-30 (SPD)
    		Always
    		Below 1 Ω
    G19-6 (+S) or G148-30 (SPD) - Body ground
    		Always
    		10 kΩ or higher

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


6.REPLACE ECM

  1. Replace the ECM (HILUX_TGN26 RM0000013Z001HX.html).



NEXT
Go to step 10

7.CHECK SPEEDOMETER CIRCUIT

  1. Check the speedometer circuit (HILUX_TGN26 RM0000011IY01VX.html).

    HINT:
    Inspect the brake actuator assembly and speed sensor.


NEXT
Go to step 10

8.REPLACE COMBINATION METER ASSEMBLY

  1. Replace the combination meter assembly (HILUX_TGN26 RM000000THS02OX.html).



NEXT
Go to step 10

9.REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. Repair or replace the harness or connector.


NEXT


10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (HILUX_TGN26 RM000000PDK11ZX.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at 10 km/h (6.3 mph) or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the pending DTC is not output again.


NEXT

END