INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)
INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)
INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)
INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)
INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)
INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for 60/40 Split Seat Type)
INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Fixed Seat Type)
Rear Airbag Sensor (For Sedan) -- Installation |
- CAUTION:
- Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (YARIS_NCP93 RM000000KT10D1X.html).
- NOTICE:
- Always use "Torx" socket wrench E10 when removing the rear seat.
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.
| 1. INSTALL REAR AIRBAG SENSOR |
Confirm that the ignition switch is turned to off.
Confirm that the negative battery terminal is detached.
- CAUTION:
- Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.
Insert the hook into the body hole and install the airbag sensor with the bolt.
- Torque:
- 9.0 N*m{90 kgf*cm, 80 in.*lbf}
- NOTICE:
- Do not use a rear airbag sensor that has been dropped.
- Do not subject the rear airbag sensor to any impact or force.
 |
Confirm that there is no looseness by shaking the rear airbag sensor.
Connect the airbag connector.
 |
| 2. INSTALL REAR SEAT SIDE COVER RH |
Engage the 2 clips and the 4 claws and install the rear seat side cover.
 |
| 3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
- Paint mark:
Area Color RH side Green LH side Red
 |
| 4. INSTALL REAR DOOR SCUFF PLATE RH |
Engage the 7 claws and install the rear door scuff plate.
 |
| 5. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type) |
 |
w/ Grand Spare Tire:
Install the luggage compartment trim inner pad.
w/o Grand Spare Tire:
Install the luggage compartment trim inner pad.
 |
| 6. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type) |
 |
Install the spare wheel cover.
| 7. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type) |
 |
Install the luggage compartment floor mat.
| 8. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type) |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback, tightening the 2 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{375 kgf*cm, 27 ft.*lbf}
 |
Install the rear seatback cover with the 2 clips.
 |
Pull up the rear seatback.
Install the rear seat outer belt into the rear seat shoulder belt guide.
 |
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 9. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type) |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback, tightening the 2 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{375 kgf*cm, 27 ft.*lbf}
 |
Install the rear seatback cover with the 2 clips.
 |
Pull up the rear seatback.
Install the rear seat outer belt into the rear seat shoulder belt guide.
 |
| 10. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) |
Engage the 3 hooks and install the rear seatback.
 |
Tighten the 3 bolts.
- Torque:
- 7.9 N*m{80 kgf*cm, 70 in.*lbf}
Install the rear seat outer belt into the rear seat shoulder belt guide.
- HINT:
- Use the same procedure for both sides.
 |
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 11. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for 60/40 Split Seat Type) |
Pass the rear seat inner belt through the rear seat cushion cover pad slit.
 |
Engage the 3 hooks and install the rear seat cushion cover pad.
- NOTICE:
- Make sure that the 2 rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.
| 12. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Fixed Seat Type) |
Pass the rear seat inner belt through the rear seat cushion cover pad slit.
 |
Engage the 3 hooks and install the rear seat cushion cover pad.
- NOTICE:
- Make sure that the 2 rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{55 kgf*cm, 48 in.*lbf}
| 14. INSPECT SRS WARNING LIGHT |