Automatic Transaxle System (For Sedan) Data List / Active Test

Drivetrain. Yaris. Ncp93, 131
U340E Automatic Transmission Transaxle. Yaris. Ncp93, 131

  1. DATA LIST

  1. ACTIVE TEST

Automatic Transaxle System (For Sedan) -- Data List / Active Test



DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. In accordance with the display on the Techstream, read the Data List.

    Engine and ECT
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Neutral Position SW Signal
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P and N
    		When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
    HINT:
    When failure still occurs even after adjusting these parts, (YARIS_NCP93 RM000000W840PUX.html)
    Stop Light Switch
    		Stop light switch status/
    ON or OFF
    1. ON: Brake pedal is depressed
    2. OFF: Brake pedal is released
    		-
    SPD (NT)
    		Input turbine speed/
    display: 50 rpm
    min.: 0 rpm
    max.: 12750 rpm
    1. Lock-up ON (After warming up engine):
      Input turbine speed (NT) equal to engine speed
    2. Lock-up OFF (Idling in P or N position):
      Input turbine speed (NT) nearly equal to engine speed
    3. Vehicle stopped in R position: 0 rpm
    		-
    Shift SW Status (P Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    		When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
    HINT:
    When failure still occurs even after adjusting these parts, (YARIS_NCP93 RM000000W840PUX.html)
    Shift SW Status (R Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    Shift SW Status (2 Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in 2
    2. OFF: Shift lever not in 2
    Shift SW Status (L Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in L
    2. OFF: Shift lever not in L
    Shift SW Status (N Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    Shift SW Status (D Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in D
    2. OFF: Shift lever not in D
    Shift SW Status (3 Range)
    		PNP switch Status/
    ON or OFF
    1. ON: Shift lever in 3
    2. OFF: Shift lever not in 3
    A/T Oil Temperature 1
    		ATF temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    		If the value is "-40°C (-40°F)" or "150°C (302°F) or more ", ATF temperature sensor circuit is opened or shorted.
    Lock Up
    		Lock Up status/
    ON or OFF
    1. ON: Lock up operating
    2. OFF: Lock up not operating
    		-
    ST Solenoid Status
    		Shift Solenoid ST Status/
    ON or OFF
    		Up-shifting and down-shifting between 3rd and 4th gears while driving: OFF → ON → OFF
    		-
    Shift Status
    		Actual Gear Position/
    1st, 2nd, 3rd or 4th
    		Shift lever position is:
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. D: 1st, 2nd, 3rd or 4th
    		-
    SLT Solenoid Status
    		Shift Solenoid SLT Status/
    ON or OFF
    1. ON: Accelerator pedal is released
    2. OFF: Accelerator pedal is depressed
    		-
    SLU Solenoid Status
    		Shift Solenoid SLU Status/
    ON or OFF
    1. ON: Lock Up
    2. OFF: Except Lock Up
    		-
    AT Fluid
    		ATF condition
    		ATF condition
    1. ON: NG
    2. OFF: OK
    		Replace ATF when ATF condition is ON.

    Engine and ECT (for Mexico model)
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    SPD (NT)
    		Input Turbine Speed/
    display: 50 rpm
    min.: 0 rpm
    max.: 12750 rpm
    HINT:
    1. Lock-Up ON (After warming up engine):
      Input turbine speed (NT) equal to engine speed
    2. Lock-Up OFF (Idling in P or N position):
      Input turbine speed (NT) nearly equal to engine speed
    3. Vehicle stopped in D position: 0 rpm
    		-
    Neutral Position SW Signal
    		PNP SW Status/
    ON or OFF
    1. ON: Brake pedal is depressed
    2. OFF: Brake pedal is released
    		When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
    HINT:
    When failure still occurs even after adjusting these parts, (YARIS_NCP93 RM000000W840PUX.html).
    Stop Light Switch
    		Stop Light SW Status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    		-
    Shift Status
    		ECM Gearshift Command/
    1st, 2nd, 3rd or 4th
    		Shift lever position;
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. D: 1st, 2nd, 3rd or 4th
    		-
    Shift SW Status (R Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    		When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
    HINT:
    When failure still occurs even after adjusting these parts, (YARIS_NCP93 RM000000W840PUX.html).
    Shift SW Status (P Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    Shift SW Status (N Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    Shift SW Status (D Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in D or 3
    2. OFF: Shift lever not in D and 3
    Shift SW Status (3 Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in 3
    2. OFF: Shift lever not in 3
    Shift SW Status (2 Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in 2
    2. OFF: Shift lever not in 2
    Shift SW Status (L Range)
    		PNP SW Status/
    ON or OFF
    1. ON: Shift lever in L
    2. OFF: Shift lever not in L
    A/T Oil Temperature 1
    		ATF (Automatic Transmission Fluid) Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test: Approximately 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    		If value is "-40°C (-40°F)" or "150°C (302°F) or more", ATF temperature sensor circuit is open or short.
    AT Fluid
    		ATF Condition
    		ATF Condition;
    NG: ON
    OK: OFF
    		Replace ATF when ATF condition is ON.
    Lock Up
    		Lock Up Status/
    ON or OFF
    1. ON: Lock Up
    2. OFF: Except Lock Up
    		-
    Lock Up Solenoid Status
    		Lock Up Solenoid Status/
    ON or OFF
    1. ON: Lock up solenoid ON
    2. OFF: Lock up solenoid OFF
    		-
    ST Solenoid Status
    		Shift Solenoid ST Status/
    ON or OFF
    		Up-shifting and down-shifting between 3rd and 4th gears while driving:
    OFF → ON → OFF
    		-
    SLU Solenoid Status
    		Shift Solenoid SLU Status/
    ON or OFF
    1. ON: Lock Up
    2. OFF: Except Lock Up
    		-
    SLT Solenoid Status
    		Shift Solenoid SLT Status/
    ON or OFF
    1. ON: Accelerator pedal is released
    2. OFF: Accelerator pedal is depressed
    		-


ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Select the following items: Powertrain / Engine and ECT / Active Test.

  7. In accordance with the display on the Techstream, perform the Active Test.

    Engine and ECT
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Activate the Solenoid (SLU)
    		[Test Details]
    Operate shift solenoid SLU
    		ON/OFF
    		[Vehicle Condition]
    1. Vehicle Stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    		[Test Details]
    Operate shift solenoid SLT and raise the line pressure.
    		ON/OFF
    		[Vehicle Condition]
    1. Vehicle Stopped
    2. Engine idling
    HINT:
    OFF: Line pressure up (When the active test of "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off.)
    ON: No action (normal operation)
    Activate the Solenoid (S1)
    		[Test Details]
    Operate shift solenoid S1
    		ON/OFF
    		[Vehicle Condition]
    1. Engine Stopped
    2. Shift lever in P or N
    Activate the Solenoid (S2)
    		[Test Details]
    Operate shift solenoid S2
    		ON/OFF
    		[Vehicle Condition]
    1. Engine Stopped
    2. Shift lever in P or N
    Activate the Lock Up
    		[Test Details]
    Control shift solenoid SLU to set automatic transaxle to lock-up condition.
    		ON/OFF
    		Possible to check SLU operation.
    [Vehicle Condition]
    Vehicle Speed: 60 km/h (36 mph) or more, and 4th gear
    Control the Shift Position
    		[Test Details]
    Operate shift solenoid valve and set each shift position manually.
    1. Press →button: Shift up
    2. Press ←button: Shift down
    1st/2nd/3rd/4th
    		Possible to check operation of shift solenoid valves.
    [Vehicle Condition]
    Vehicle Speed: Less than 50 km/h (30 mph)
    Activate the Solenoid (ST)
    		[Test Details]
    Operate shift solenoid ST
    		ON/OFF
    		[Vehicle Condition]
    1. Vehicle Stopped
    2. Engine idling
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test (YARIS_NCP93 RM000000W7B0IJX.html) as well.

    HINT:
    The pressure values in Active Test and Hydraulic Test are different from each other.