Knock Sensor (For Sedan) Installation

Engine Hybrid System. Yaris. Ncp93, 131
1Nz-Fe Engine Control. Yaris. Ncp93, 131

  1. INSTALL KNOCK SENSOR

  2. INSTALL INTAKE MANIFOLD

  3. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

  4. CONNECT WATER BY-PASS HOSE NO. 2

  5. CONNECT WATER BY-PASS HOSE

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE NO. 1

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  8. ADD ENGINE COOLANT

  9. CHECK FOR ENGINE COOLANT LEAKAGE

  10. INSTALL CYLINDER HEAD COVER NO. 2

Knock Sensor (For Sedan) -- Installation



1. INSTALL KNOCK SENSOR


Yaris. Ncp93, 131.1Nz-Fe Engine Control.Sfi System (For Sedan).Knock Sensor (For Sedan)  Installation
  1. Install the knock sensor with the nut as shown in the illustration.

    Torque:
    20 N*m{204 kgf*cm, 15 ft.*lbf}
  1. Connect the knock sensor connector.



2. INSTALL INTAKE MANIFOLD
  1. Install a new gasket onto the intake manifold.



    Yaris. Ncp93, 131
  1. Install the intake manifold with the 3 bolts and 2 nuts.

    Torque:
    30 N*m{304 kgf*cm, 22 ft.*lbf}


    Yaris. Ncp93, 131
  1. Connect the union to connector tube hose.



    Yaris. Ncp93, 131
  1. Connect the ventilation hose.



    Yaris. Ncp93, 131
  1. Install water by-pass hose No. 2.



    Yaris. Ncp93, 131
  1. Install the engine wire harness onto the intake manifold.



3. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY


Yaris. Ncp93, 131
  1. Install a new gasket onto the intake manifold.



    Yaris. Ncp93, 131
  1. Install the throttle with motor body assembly using the bolt and 3 nuts.

    Torque:
    9.0 N*m{92 kgf*cm, 80 in.*lbf}


    Yaris. Ncp93, 131
  1. Install the water filler sub-assembly with hose using the 2 nuts.

    Torque:
    7.5 N*m{76 kgf*cm, 66 in.*lbf}


    Yaris. Ncp93, 131
  1. Install the wire harness with bracket using the nut.

    Torque:
    9.0 N*m{92 kgf*cm, 80 in.*lbf}
  1. Connect the throttle with motor body assembly connector.



4. CONNECT WATER BY-PASS HOSE NO. 2


Yaris. Ncp93, 131
  1. Connect water by-pass hose No. 2.



5. CONNECT WATER BY-PASS HOSE


Yaris. Ncp93, 131
  1. Connect the water by-pass hose.



6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE NO. 1


Yaris. Ncp93, 131
  1. Install air cleaner cap sub-assembly with air cleaner hose No. 1.

  1. Tighten the hose clamp to the specified torque.

    Torque:
    3.0 N*m{31 kgf*cm, 27 in.*lbf}


    Yaris. Ncp93, 131
  1. Connect the wire harness clamp and mass air flow meter connector.



    Yaris. Ncp93, 131
  1. Connect ventilation hose No. 2.



    Yaris. Ncp93, 131
  1. Connect the vacuum switching valve assembly connector and wire harness clamp.

  1. Connect fuel vapor feed hose No. 1 and fuel vapor feed hose No. 2 to the vacuum switching valve assembly.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque:
5.4 N*m{55 kgf*cm, 48 in.*lbf}


8. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    M/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    A/T 4.7 liters (5.0 USqts, 4.4 lmp. qts)
    NOTICE:
    Do not substitute water for engine coolant.
    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when when the coolant starts to flow inside the hose.
    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

    3. Press the No. 2 radiator hose and No. 3 radiator hose several times by hand to bleed air.

      NOTICE:
      When pressing the radiator houses
      1. Wear protective glove.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away form the radiator fan.
  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.



9. CHECK FOR ENGINE COOLANT LEAKAGE
CAUTION:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


    Yaris. Ncp93, 131
  1. Fill the radiator assembly with engine coolant, and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leaks. If there are no signs or traces of external engine coolant leaks, check the heater core, cylinder block and head.



10. INSTALL CYLINDER HEAD COVER NO. 2


Yaris. Ncp93, 131.1Nz-Fe Engine Control.Sfi System (For Sedan).Knock Sensor (For Sedan)  Installation
  1. Tighten the 2 A nuts, then the 2 B nuts.

    Torque:
    7.0 N*m{71 kgf*cm, 62 in.*lbf}