Spiral Cable Installation

Vehicle Interior. Corolla. Zre142 Aze141
Supplemental Restraint Systems. Corolla. Zre142 Aze141

  1. INSTALL SPIRAL CABLE (w/o VSC)

  2. INSTALL SPIRAL CABLE (w/ VSC)

  3. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR (w/ VSC)

  4. INSTALL UPPER STEERING COLUMN COVER

  5. INSTALL LOWER STEERING COLUMN COVER

  6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

  7. ADJUST SPIRAL CABLE

  8. INSTALL STEERING WHEEL ASSEMBLY

Spiral Cable -- Installation



1. INSTALL SPIRAL CABLE (w/o VSC)

  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the turn signal switch pin may be snapped.


    Corolla. Zre142 Aze141

  1. Install the spiral cable with the 3 claws.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable.

    NOTICE:
    When connecting the airbag connector, take care not to damage the airbag wire harness.

  1. w/ Horn Button Wire Harness:

    1. Connect the connector to install the horn button wire sub-assembly.



2. INSTALL SPIRAL CABLE (w/ VSC)


    Corolla. Zre142 Aze141.Supplemental Restraint Systems.Airbag System.Spiral Cable Installation

  1. Install the spiral cable to the steering angle sensor with the 6 claws and 2 pins.



3. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR (w/ VSC)

  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the turn signal switch pin may be snapped.


    Corolla. Zre142 Aze141

  1. Install the spiral cable with steering angle sensor with the 3 claws.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable with steering angle sensor.

    NOTICE:
    When connecting the airbag connector, take care not to damage the airbag wire harness.

  1. w/ Horn Button Wire Harness:

    1. Connect the connector to install the horn button wire sub-assembly.



4. INSTALL UPPER STEERING COLUMN COVER


    Corolla. Zre142 Aze141

  1. Engage the claw and the 2 pins, and install the upper steering column cover.



5. INSTALL LOWER STEERING COLUMN COVER
NOTICE:
If the lower steering column cover is installed in the incorrect order, it will not be possible to assemble the lower steering column cover.


    Corolla. Zre142 Aze141

  1. Engage the 2 claws to install the lower steering column cover.



    Corolla. Zre142 Aze141

  1. Engage the 4 claws.



    Corolla. Zre142 Aze141

  1. Engage the claw.

    HINT:
    Press the area around the claw to engage it.


6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    Corolla. Zre142 Aze141

  1. Engage the 5 claws, 2 clips and 2 guides.



    Corolla. Zre142 Aze141

  1. Install the lower instrument panel finish panel sub-assembly with the 2 screws <B>.



7. ADJUST SPIRAL CABLE

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    Corolla. Zre142 Aze141

  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.


    Corolla. Zre142 Aze141.Supplemental Restraint Systems.Airbag System.Spiral Cable Installation

  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.
    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


8. INSTALL STEERING WHEEL ASSEMBLY
(COROLLA_ZRE142 RM0000035Q201KX_01_0029.html)