Steering Pad Switch Installation

for Type A:

1. Engage the 2 pins and install the steering pad switch LH.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the clamp.
   

4. Connect the connector to the spiral cable.
   

for Type B:

1. Engage the 2 pins and claw to install the steering pad switch LH.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Connect the connector to the spiral cable.
   

for Type A:

1. Engage the 2 pins and install the steering pad switch assembly.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the clamp.
   

4. Engage the 2 pins and install the steering pad switch.
   

5. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

6. Engage the clamp.
   

7. Connect the connector to the spiral cable.
   

for Type B:

1. Engage the 2 pins and claw to install the steering pad switch assembly.
   

2. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

3. Engage the 2 pins and claw to install the steering pad switch.
   

4. Install the screw.
   

   Torque:

   2.4 N*m{24 kgf*cm, 21 in.*lbf}

5. Connect the connector to the spiral cable.
   

for Type A:

1. Check that the ignition switch is off.
   

2. Check that the cable is disconnected from the negative (-) battery terminal.
   

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.





3. Connect the 2 airbag connectors to the steering pad.
   

   NOTICE:

   When connecting any airbag connector, take care not to damage the airbag wire harness.

4. Push in the 2 locks to install the airbag connectors.
   

5. Connect the horn connector to the steering pad.
   

6. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
   





7. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
   
   

   
   
   
   
   

   Text in Illustration

   *A	w/o Steering Pad Switch	*B	w/ Steering Pad Switch
   *1	"Torx" Screw	*2	Screw Case

   Torque:

   8.8 N*m{90 kgf*cm, 78 in.*lbf}

for Type B:

1. Check that the ignition switch is off.
   

2. Check that the cable is disconnected from the negative (-) battery terminal.
   

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.





3. Connect the 2 airbag connectors to the steering pad.
   

   NOTICE:

   When connecting any airbag connector, take care not to damage the airbag wire harness.

4. Push in the 2 locks to install the airbag connectors.
   

5. Connect the horn connector to the steering pad.
   





6. Push the steering pad to engage the 2 pins.
   

   NOTICE:

   Make sure that the pins are securely inserted into the steering wheel holes.

for Type A:

1. Engage the claw to install the lower No. 3 steering wheel cover.
   

for Type B:

1. Engage the 2 claws to install the lower No. 3 steering wheel cover.
   

for Type A:

1. Engage the claw to install the lower No. 2 steering wheel cover.
   

for Type B:

1. Engage the 2 claws to install the lower No. 2 steering wheel cover.
   

Make sure that the horn sounds.

HINT:

If the horn does not sound, inspect the horn system (COROLLA_ZRE142 RM0000016F5071X.html).