Audio And Visual System Illumination Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ILLUMINATION

CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

INSPECT STEERING PAD SWITCH ASSEMBLY

INSPECT SPIRAL CABLE

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)

CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND)

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the supplemental restraint system (CAMRY_ACV40 RM000000KT1016X.html).

1. Check if the illumination for the radio receiver, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
   
   

   Result:

   
   

   Result	Proceed to
   Illumination comes on for all components except steering pad switch.	A
   Illumination comes on for all components except radio receiver.	B
   No illumination comes on (radio receiver, hazard switch, glove box, etc.).	C

1. Disconnect the spiral cable connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard voltage:

   Tester connection	Condition	Specified condition
   IL+2 - Body ground	Light control SW TAIL or HEAD	10 to 14 V

1. Disconnect the steering pad switch connector.
   

2. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.
   

   
   
   
   

3. Check if the illumination for the steering pad switch assembly comes on.
   

   OK:

   Illumination for the steering pad switch assembly comes on.
   

1. Disconnect the steering pad switch and spiral cable connectors.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard resistance:

   Tester connection	Spiral Cable Position	Specified condition
   EAU - EAU	Center	Below 1 Ω
   	2.5 rotations to the left
   	2.5 rotations to the right
   IL+2 - IL+2	Center	Below 1 Ω
   	2.5 rotations to the left
   	2.5 rotations to the right

   NOTICE:

   The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.

   HINT:

   1. Removal (CAMRY_ACV40 RM000000UWD00RX.html)
      
   2. Installation (CAMRY_ACV40 RM000000UWA00QX.html)
      

1. Disconnect the connectors from the radio receiver and spiral cable.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard resistance:

   Tester connection	Condition	Specified condition
   SWG - EAU	Always	Below 1 Ω
   SWG - Body ground	Always	10 kΩ or higher

1. Disconnect the radio receiver connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard voltage:

   Tester connection	Condition	Specified condition
   ILL+ - Body ground	Light control switch TAIL or HEAD	10 to 14 V

1. Disconnect the radio receiver connector.
   

2. Measure the resistance according to the value(s) in the table below.
   

   Standard resistance:

   Tester connection	Condition	Specified condition
   ILL- - Body ground	Always	10 kΩ or higher