Meter / Gauge System On-Vehicle Inspection

Body Electrical. Camry. Acv40 Gsv40
Meter. Camry. Acv40 Gsv40

  1. INSPECT SPEEDOMETER

  2. INSPECT TACHOMETER

  3. INSPECT ENGINE OIL PRESSURE SWITCH

  4. INSPECT MULTI-INFORMATION DISPLAY

Meter / Gauge System -- On-Vehicle Inspection



1. INSPECT SPEEDOMETER

  1. Check the operation.

    1. Using a speedometer tester (calibrated chassis dynamometer), check the speedometer indication according to the table below.

      Reference: km/h
      Chassis dynamometer indication
      		Acceptable range
      Data in ( ) is for reference
      20 km/h
      		21.0 to 25.0 km/h
      40 km/h
      		41.7 to 46.2 km/h
      60 km/h
      		62.7 to 67.2 km/h
      80 km/h
      		83.4 to 88.4 km/h
      100 km/h
      		104.3 to 109.3 km/h
      120 km/h
      		125.1 to 130.6 km/h
      140 km/h
      		145.8 to 151.8 km/h
      160 km/h
      		166.2 to 173.2 km/h
      180 km/h
      		188.9 to 194.5 km/h
      200 km/h
      		207.7 to 215.7 km/h
      220 km/h
      		228.4 to 236.8 km/h
      240 km/h
      		249.2 to 258.0 km/h
      NOTICE:
      Tire wear as well as over or under inflation will cause errors.

    2. Check the deviation from the acceptable range of the speedometer indication.

      Reference:
      Less than 0.5 km/h (0.3 mph)
      HINT:
      If the indication is not as specified, go to problem symptoms table (CAMRY_ACV40 RM0000012GB03BX.html).


2. INSPECT TACHOMETER

  1. Connect a tune-up tachometer, and start the engine.

  1. Compare the test results with the tachometer indications.

    DC 13.5 V, at 25°C (77°F)
    Tune-up tachometer indication (rpm)
    		Acceptable range
    Data in ( ) is for reference
    700
    		630 to 770
    1,000
    		(900 to 1,100)
    2,000
    		(1,850 to 2,150)
    3,000
    		2,800 to 3,200
    4,000
    		(3,800 to 4,200)
    5,000
    		4,800 to 5,200
    6,000
    		(5,750 to 6,250)
    7,000
    		6,700 to 7,300
    8,000
    		(7,700 to 8,300)
    HINT:
    If the indication is not as specified, go to the problem symptoms table (CAMRY_ACV40 RM0000012GB03BX.html).


3. INSPECT ENGINE OIL PRESSURE SWITCH

  1. Disconnect the connector from the engine oil pressure switch.

  1. Turn the ignition switch to the ON position.

  1. Ground the terminal of the wire harness side connector.

  1. Turn the ignition switch to the ON position, and engine idling for 10 seconds or more.

    OK:
    The warning message is displayed.
    HINT:
    If the warning light or message is not displayed, go to the problem symptoms table (CAMRY_ACV40 RM0000012GB03BX.html).


4. INSPECT MULTI-INFORMATION DISPLAY


    Camry. Acv40 Gsv40.Meter.Meter / Gauge System.Meter / Gauge System On-Vehicle Inspection

  1. Turn the ignition switch off.

  1. Press the "DISP" button and hold it down.

  1. Turn the ignition switch to the ON position.

    OK:
    All the dots in the multi-information display come on.
    HINT:
    This test is also available on "Active Test" (CAMRY_ACV40 RM0000012GB03BX.html).

  1. Ignition switch off to finish this test mode.

    HINT:
    If the result is not as specified, replace the combination meter assembly.