Heater & Air Conditioning System. Camry. Acv40 Gsv40
Air Conditioning. Camry. Acv40 Gsv40
Air Conditioning System -- Data List / Active Test |
| DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
Air Conditioner: Item Measurement Item / Display (Range) Normal Condition Diagnostic Note Room Temperature Sensor
(Room Temp)Room temperature sensor / Min.: -6.5°C (20.3°F), Max.: 57.25°C (135.05°F) Actual cabin temperature is displayed - Ambient Temp Sensor
(Ambi Temp Sens)Ambient temperature sensor / Min.: -23.3°C (-9.94°F), Max.: 65.95°C (150.71°F) Actual ambient temperature is displayed - Adjusted Ambient Temp
(Ambi Temp)Adjusted ambient temperature / Min.: -30.8°C (-23.44°F), Max.: 50.8°C (123.44°F) - - Evaporator Fin Thermistor
(Evap Fin Temp)Evaporator fin thermistor / Min.: -29.7°C (-21.46°F), Max.: 59.55°C (139.19°F) Actual evaporator temperature is displayed - Solar Sensor (D side)
(Solar Sens-D)Driver side solar sensor / Min.: 0, Max.: 255 Driver side solar sensor value increases as brightness increases - Solar Sensor (P side)
(Solar Sens-P)Passenger side solar sensor / Min.: 0, Max.: 255 Passenger side solar sensor value increases as brightness increases - Engine Coolant Temp
(Coolant Temp)Engine coolant temperature / Min.: 1.3°C (34.34°F), Max.: 90.55°C (194.99°F) Actual engine coolant temperature is displayed while engine is warmed up - Set Temperature (D side)
(Set Temp-D)Driver side set temperature / Min.: 0°C (32°F), Max.: 30°C (54°F) Driver side set temperature is displayed - Set Temperature (P side)
(Set Temp-P)Passenger side set temperature / Min.: 0°C (32°F), Max.: 30°C (54°F) Passenger side set temperature is displayed - Estimated Temp-D
(Estimate Temp-D)Driver side estimate temperature / Min.: -358.4°C (-613.12°F), Max.: 358.4°C (677.12°F) Damper is at "MAX. COOL": -358.4°C (-613.12°F)
Damper is at "MAX. HOT": 358.4°C (677.12°F)- Estimated Temp-P
(Estimate Temp-P)Passenger side estimate temperature / Min.: -358.4, Max.: 358.4 Damper is at "MAX. COOL": -358.4°C (-613.12°F)
Damper is at "MAX. HOT": 358.4°C (677.12°F)- Blower Motor Speed Level
(Blower Level)Blower motor speed level / Min.: 0 level, Max.: 31 level Increases in the range between 0 and 31 as the blower motor speed increases - Regulator Pressure Sensor
(Reg Press Sens)Regulator pressure sensor / Min.: -0.5 kgf/cm2G, Max.: 37.75 kgf/cm2G Actual refrigerant pressure is displayed - Regulator Control Current
(Reg Ctrl Currnt)Compressor variable output current / Min.: 0 A, Max.: 0.996 A - - Air Mix Servo Target Pulse(D)
(Air Mix Pulse-D)Driver side air mix servo motor target pulse / Min.: 0, Max.: 255 LHD:- MAX. COLD: 5 (pulse)
- MAX. HOT: 103 (pulse)
RHD:- MAX. COLD: 105 (pulse)
- MAX. HOT: 7
- Air Mix Servo Targ Pulse(P)
(Air Mix Pulse-P)Passenger side air mix servo motor target pulse / Min.: 0, Max.: 255 LHD:- MAX. COLD: 105 (pulse)
- MAX. HOT: 7 (pulse)
RHD:- MAX. COLD: 5
- MAX. HOT: 103
- Air Outlet Servo Pulse (D)
(Air Out Pulse-D)Driver side air outlet servo motor target pulse / Min.: 0, Max.: 255 FACE: 8 (pulse)
B/L: 30 to 38 (pulse)
FOOT: 50 to 74 (pulse)
FOOT/DEF: 80 (pulse)
DEF: 97 (pulse)- Air Inlet Damper Target Pulse
(A/I Damp Targ Pls)Air inlet damper target pulse / Min.: 0, Max.: 255 RECIRCULATION: 7 (pulse)
FRESH: 28 (pulse)- Number of Trouble Codes
(#Codes)Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs will be displayed - Engine: Item Measurement Item / (Range) Display Normal Condition Diagnostic Note A/C Signal
(A/C Signal)A/C signal / ON or OFF ON: A/C ON
OFF: A/C OFF- A/C Magnetic Clutch Relay
(A/C Mag Clutch)A/C magnetic clutch relay / ON or OFF ON: A/C magnetic clutch ON
OFF: A/C magnetic clutch OFF- - MAX. COLD: 5 (pulse)
| ACTIVE TEST |
- HINT:
- Performing the intelligent tester's Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed in the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
Perform the Active Test by referring to the table below.
Air Conditioner: Item Test Details / Display (Range) Diagnostic Note Blower Motor
(Blower Motor)Blower motor / Min.: Level 0, Max.: Level 31 - Defogger Relay (Rear)
(Defogger Rly-R)Defogger relay (Rear) / OFF, ON - Air Mix Servo Targ Pulse(D)
(Air Mix Pulse-D)Driver side air mix servo motor pulse / Min.: 0, Max.: 255 - Air Mix Servo Targ Pulse(P)
(Air Mix Pulse-P)Passenger side air mix servo motor pulse / Min.: 0, Max.: 255 - Air Outlet Servo Pulse (D)
(Air Out Pulse-D)Driver side air outlet servo motor pulse / Min.: 0, Max.: 255 - Air Inlet Damper Targ Pulse
(A/I Damp Targ Pls)Air inlet damper target pulse / Min.: 0, Max.: 255 - Engine: Item Test Details / Display (Range) Diagnostic Note A/C Magnet Clutch
(Control the A/C Magnet Clutch)Magnetic clutch relay / ON or OFF -