Steering Lock System Data List / Active Test

Steering. Camry. Acv40 Gsv40
Steering Column. Camry. Acv40 Gsv40

  1. DATA LIST

  1. ACTIVE TEST

Steering Lock System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Body / Entry & Start / Data List.

  6. According to the display on the intelligent tester, read the Data List.

    Entry & Start
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Slck Sleep Cond
    		Steering lock ECU sleep condition / YES or NO
    		YES: Steering lock ECU sleep mode can be entered
    NO: Steering lock ECU sleep mode cannot be entered
    		-
    Slck Start Cond
    		Steering lock ECU start signal / YES or NO
    		YES: Steering lock ECU sent a start signal
    NO: Steering lock ECU did not send a start signal
    		-
    Eng Start Cond
    		Engine start condition / OK or NG
    		OK: Engine is allowed to start
    NG: Engine is not allowed to start
    		-
    Sensor Value
    		Sensor malfunction / NG (PAST) or OK
    		NG (PAST): Sensor malfunction
    OK: No malfunction
    		-
    Pwr Supply Shrt
    		Short in ECU / NG (PAST) or OK
    		NG (PAST): Short in ECU
    OK: No malfunction
    		-
    Pwr Supply Open
    		Open in ECU / NG (PAST) or OK
    		NG (PAST): Open in ECU
    OK: No malfunction
    		-
    Mtr Driver Shrt
    		Short in driver ECU / NG (PAST) or OK
    		NG (PAST): Short in driver ECU
    OK: No malfunction
    		-
    Mtr Driver Open
    		Open in driver ECU / NG (PAST) or OK
    		NG (PAST): Open in driver ECU
    OK: No malfunction
    		-
    Lck/Unlck Rec
    		Steering lock command reception record / YES or NO
    		YES: Steering lock/unlock signal received
    NO: Steering lock/unlock signal no received
    		-
    Lck Bar Stuck
    		Lock bar stuck malfunction / NG (PAST) or OK
    		NG (PAST): Lock bar stuck malfunction
    OK: No malfunction
    		-
    Push Start Err
    		Push button start function malfunction / NG (PAST) or OK
    		NG (PAST): Malfunction in push button start
    OK: No malfunction
    		-
    IG2
    		IG2 voltage / ON or OFF
    		ON: 10 to 14 V
    OFF: Below 1 V
    		-
    IG (Lin)
    		LIN bus IG status / ON or OFF
    		ON: LIN bus IG ON status
    OFF: LIN bus IG OFF status
    		-


ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Body / Combination Meter / Active Test.

  6. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Security Ind
    		Security Indicator
    		ON or OFF
    		-