Entry And Start System Data List / Active Test

Engine. Camry. Acv40 Gsv40
2Gr-Fe Starting. Camry. Acv40 Gsv40

  1. READ DATA LIST

  1. PERFORM ACTIVE TEST

Entry And Start System -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful as intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.

  4. Enter the following menus: Body / Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Body:
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ACC SW
    		Engine switch on (ACC) / ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    IG SW
    		Engine switch on (IG) / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    Stop Light SW
    		Stop light switch / ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    St SW1
    		Start switch 1 / ON or OFF
    		ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    		-
    St SW2
    		Start switch 2 / ON or OFF
    		ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    		-
    Str Unlock SW
    		Steering lock condition / ON or OFF
    		ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    		-
    N SW / C SW
    		Neutral start switch / ON or OFF
    		ON: Shift position is P or N
    OFF: Shift position is neither P nor N
    		-
    Shift P Sig
    		Shift P position signal / ON or OFF
    		ON: Shift position is P
    OFF: Shift position is not P
    		-
    Vehicle Spd Sig
    		Vehicle speed signal / STOP or RUN
    		STOP: Vehicle is stopped
    RUN: Vehicle is running
    		-
    E/G Cond
    		Engine condition / STOP or RUN
    		STOP: Engine is stopped
    RUN: Engine is running
    		-
    IG1 Relay Mon 1
    		IG1 outer relay monitor / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Mon 1
    		IG2 outer relay monitor / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG1 Relay Mon 2
    		IG1 inner relay monitor / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    IG2 Relay Mon 2
    		IG2 inner relay monitor / ON or OFF
    		ON: Engine switch on (IG)
    OFF: Engine switch off
    		-
    ACC Relay Mon
    		ACC relay monitor / ON or OFF
    		ON: Engine switch on (ACC)
    OFF: Engine switch off
    		-
    Latch Circuit
    		Latch circuit / ON or OFF
    		ON: Engine switch on (IG) or engine running
    OFF: Engine switch off or on (ACC)
    		-
    Start Req Sig
    		Starter request signal monitor / ON or OFF
    		ON: ST relay is ON
    OFF: ST relay is OFF
    		Engine switch pressed and held with shift lever in P or N
    Pwr Cond
    		Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
    		ALL: All relays are OFF
    ACC ON: ACC relay is ON
    IG1: IG1 relay is ON
    IG2: IG2 relay is ON
    ST ON: ST request signal is ON
    		-
    ACC Cut Sig
    		ACC relay cut signal / ON or OFF
    		ON: Engine is cranking
    OFF: Engine is not cranking
    		-
    ST Relay Mon
    		STARTER relay monitor / ON or OFF
    		ON: Engine is cranking
    OFF: Engine is not cranking
    		Engine is cranking with engine switch on (IG) and shift lever in P or N
    Comm Smrt/Wrls
    		Communication for certification ECU / OK or STOP
    		OK: Communication
    STOP: No communication
    		-


PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester Active Test allows the relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.


Body:
Tester Display
Test Part
Control Range
Diagnostic Note
Lighting Ind
Indicator for lighting
ON / OFF
-
Ind Condition
Engine switch indicator
Green / Amber / No Sig
-
S Lock Pwr
Power supply for steering lock ECU
ON / OFF
-