Engine Coolant Temperature Sensor Installation

Engine. Camry. Acv40 Gsv40
2Az-Fe Engine Control System. Camry. Acv40 Gsv40

  1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

  2. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  4. INSTALL AIR CLEANER INLET ASSEMBLY

  5. ADD ENGINE COOLANT

  6. CHECK FOR ENGINE COOLANT LEAKS

Engine Coolant Temperature Sensor -- Installation



1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR


    Camry. Acv40 Gsv40.2Az-Fe Engine Control System.Sfi System.Engine Coolant Temperature Sensor Installation

  1. Install a new gasket onto the engine coolant temperature sensor.

  1. Using SST, install the engine coolant temperature sensor.

    SST
    09817-33190
    Torque:
    20 N*m{204 kgf*cm, 15 ft.*lbf}

  1. Connect the engine coolant temperature sensor connector.



2. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    Camry. Acv40 Gsv40

  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}

  1. Connect the hose clamp.



3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. Install the air cleaner filter element onto the air cleaner case.



    Camry. Acv40 Gsv40

  1. Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.



    Camry. Acv40 Gsv40.2Az-Fe Engine Control System.Sfi System.Engine Coolant Temperature Sensor Installation

  1. Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    Make sure that the hose clamp is at the correct angle.


    Camry. Acv40 Gsv40.2Az-Fe Engine Control System.Sfi System.Engine Coolant Temperature Sensor Installation

  1. Connect the No. 2 ventilation hose to the air cleaner hose.



    Camry. Acv40 Gsv40.2Az-Fe Engine Control System.Sfi System.Engine Coolant Temperature Sensor Installation

  1. Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).



4. INSTALL AIR CLEANER INLET ASSEMBLY


    Camry. Acv40 Gsv40

  1. Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{51 kgf*cm, 44 in.*lbf}


5. ADD ENGINE COOLANT

  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{130 kgf*cm, 9 ft.*lbf} for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.2 liters (6.6 US qts, 5.5 lmp. qts)
    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



6. CHECK FOR ENGINE COOLANT LEAKS


Camry. Acv40 Gsv40
NOTICE:
Before performing each inspection, turn the A/C switch OFF.
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.