Can Communication System Steering Angle Sensor Communication Stop Mode

Communication System. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Can Communication. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

CAN COMMUNICATION SYSTEM - Steering Angle Sensor Communication Stop Mode


DESCRIPTION


Detection Item
Symptom
Trouble Area
Steering Angle Sensor Communication Stop Mode
Either condition is met:
  1. "Steering Angle Sensor" is not displayed on "Bus Check".
  2. "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside steering angle sensor
  2. Steering angle sensor branch wire or connector
  3. Steering angle sensor
HINT:
For vehicles for a 2WD with vehicle stability control system and 4WD only.

WIRING DIAGRAM


Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System Steering Angle Sensor Communication Stop Mode


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the main wire and the branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  3. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    NOTICE:
    1. w/ Navigation System (for HDD):
      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System Steering Angle Sensor Communication Stop Mode

  1. Disconnect the E95 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    E95-3 (CANH) - E95-2 (CANL)
    		Ignition switch off
    		54 to 69 Ω


NG
REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


    Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Can Communication.Can Communication System.Can Communication System Steering Angle Sensor Communication Stop Mode

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E95-1 (ESS) - Body ground
    		Always
    		Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E95-5 (BAT) - Body ground
    		Always
    		11 to 14 V
    E95-4 (IG) - Body ground
    		Ignition switch on (IG)
    		11 to 14 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR