Active Torque Control 4Wd System Dtc Check / Clear

Drive Line. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
Differential. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

  1. CHECK DTC (When Using Intelligent Tester)

  1. CLEAR DTC (When Using Intelligent Tester)

  1. CHECK DTC (When not Using Intelligent Tester)

  1. CLEAR DTC (When not Using Intelligent Tester)

Active Torque Control 4Wd System -- Dtc Check / Clear


Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Differential.Active Torque Control 4Wd System.Active Torque Control 4Wd System Dtc Check / Clear

CHECK DTC (When Using Intelligent Tester)

  1. Check the DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Read the DTCs by following the prompts on the tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

CLEAR DTC (When Using Intelligent Tester)

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Operate the intelligent tester to clear the codes.
    Refer to the intelligent tester operator's manual for further details.

Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Differential.Active Torque Control 4Wd System.Active Torque Control 4Wd System Dtc Check / Clear

CHECK DTC (When not Using Intelligent Tester)

  1. Using the SST, connect terminals TC (13) and CG (4) of the DLC3

    SST
    09843-18040

  2. Turn the ignition switch on (IG).



    3. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35.Differential.Active Torque Control 4Wd System.Active Torque Control 4Wd System Dtc Check / Clear

  3. w/o Multi-information display:
    Read DTCs from the 4WD indicator light on the combination meter.

  4. w/ Multi-information display:
    Read DTCs from the 4WD indicator light and the multi-information display on the combination meter.

    HINT:
    1. If the 4WD indicator light does not blink, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.
    2. If more than 1 DTC is detected at the same time, the DTCs will be displayed in numerical order.
    3. As an example, the blinking patterns of the normal system code and DTCs 11 and 21 are shown in the illustration.
    4. DTCs are explained in "DIAGNOSTIC TROUBLE CODE CHART" (RAV4_ACA30 RM0000020AY00VX.html).
    Section Title
    		See Procedure
    4WD Indicator Light does not Come ON
    		RAV4_ACA30 RM0000020BK00JX.html
    TC and CG Terminal Circuit
    		RAV4_ACA30 RM0000020B700OX.html

CLEAR DTC (When not Using Intelligent Tester)

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    SST
    09843-18040

  2. Turn the ignition switch on (IG).



    3. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35

  3. Clear the DTCs stored in the 4WD control ECU by depressing the brake pedal 8 times or more within 5 seconds.

  4. Check that the warning light blinks in the normal system code pattern.

  5. Remove SST from the terminals of the DLC3.

  6. Turn the ignition switch off.

    HINT:
    DTCs cannot be cleared by disconnecting the cable from the negative (-) battery terminal or removing the ECU-IG1 fuse.