Dtc P0115 Engine Coolant Temperature Circuit Malfunction
Engine. Toyota Rav4. Aca30, 33, 38 Gsa33 Zsa30, 35
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK DTC OUTPUT
READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP)
CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR OPEN IN SENSOR)
CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR)
CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
DTC P0115 Engine Coolant Temperature Circuit Malfunction |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
DESCRIPTION
A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.- HINT:
- When any of DTCs P0115, P0117 and P0118 are set, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
DTC No.
| Proceed to
| DTC Detection Condition
| Trouble Area
|
P0115
| Step 2
| Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
| - Open or short in ECT sensor circuit
- ECT sensor
- ECM
|
P0117
| Step 6
| Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
| - Short in ECT sensor circuit
- ECT sensor
- ECM
|
P0118
| Step 4
| Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
| - Open in ECT sensor circuit
- ECT sensor
- ECM
|
- HINT:
- When any of these DTCs are set, check the ECT by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.
Temperature Displayed
| Malfunction
|
-40°C (-40°F)
| Open circuit
|
140°C (284°F) or higher
| Short circuit
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (RAV4_ACA30 RM000000PDS09FX.html).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
| Proceed to
|
P0115
| A
|
P0117
| B
|
P0118
| C
|
2.READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- Between 80°C and 97°C (176°F and 207°F) with warm engine.
- Result:
Temperature Displayed
| Proceed to
|
-40°C (-40°F)
| A
|
140°C (284°F) or higher
| B
|
Between 80°C and 97°C (176°F and 207°F)
| C
|
- HINT:
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.
3.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR OPEN IN SENSOR) |
Confirm the good connection of the sensor.
Disconnect the engine coolant temperature (ECT) sensor connector.
Connect the terminals 1 and 2 of the ECT sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- 140°C (284°F) or higher
Reconnect the ECT sensor connector.
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
| Specified Condition
|
THW (B96-79) - THW (B4-2)
| Below 1 Ω
|
ETHW (B96-78) - E2 (B4-1)
| Below 1 Ω
|
Reconnect the ECM connector.
Reconnect the ECT connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR) |
Disconnect the ECT sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- -40°C (-40°F)
Reconnect the ECT sensor connector.
6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
| Specified Condition
|
THW (B96-79) or THW (B4-2) - Body ground
| 10 kΩ or higher
|
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|