Front Door Window Frame Moulding Installation


  1. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

  2. INSTALL FRONT DOOR WEATHERSTRIP LH

  3. INSTALL FRONT DOOR BELT MOULDING LH

  4. INSTALL FRONT DOOR GLASS RUN LH

  5. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

  6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

  7. INSTALL FRONT DOOR SERVICE HOLE COVER LH

  8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

  9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  10. INSTALL ASSIST GRIP COVER LH

  11. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

  12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  14. ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)

Front Door Window Frame Moulding -- Installation


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.
    Standard:
    Item
    		Temperature
    Vehicle Body
    		40 to 60°C (104 to 140°F)
    Window Frame Moulding
    		20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body or window frame moulding excessively.


1. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new front door rear window frame moulding.

    1. Using a heat light, heat a new front door rear window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the front door rear window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the front door rear window frame moulding.

      HINT:
      Press the front door rear window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.



2. INSTALL FRONT DOOR WEATHERSTRIP LH

  1. Attach the 3 clips to install the upper part of the front door weatherstrip.



3. INSTALL FRONT DOOR BELT MOULDING LH

  1. Attach the 6 claws to install the front door belt moulding.



4. INSTALL FRONT DOOR GLASS RUN LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Install the front door glass run.



5. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolt installation locations can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system (LandCruiser RM000003YMF011X.html).


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Installation

  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Installation

  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    5.5 N*m{56 kgf*cm, 49 in.*lbf}
    HINT:
    Tighten the bolts in the order shown in the illustration.


6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

  1. Attach the claw to install the outer rear view mirror, and then install the 3 nuts.

    Torque:
    8.0 N*m{82 kgf*cm, 71 in.*lbf}

  1. Connect the connector.



7. INSTALL FRONT DOOR SERVICE HOLE COVER LH

  1. Apply new butyl tape to the front door panel.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Installation

  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    Text in Illustration
    *1
    		Reference Point

  1. Attach the front door service hole cover using the reference points on the front door panel.

    NOTICE:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the seal quality.
    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 2 clamps.

  1. Install the bolt to the front door wire.



8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Install the front door inner glass weatherstrip.



9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

  1. Connect 2 connectors.

  1. w/ Seat Position Memory System:

    1. Connect the connectors.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the front door trim board sub-assembly by attaching the 4 claws of the front door inner glass weatherstrip as shown in the illustration.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 12 clips and front door trim board retainer to install the front door trim board sub-assembly.

  1. Install the 3 screws.



10. INSTALL ASSIST GRIP COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 8 claws to install the assist grip cover.



11. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Attach the 3 claws to install the inside handle bezel.



12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. Attach the 2 claws to install the front door lower frame bracket garnish.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


14. ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)
HINT:
Adjust the side television camera for the passenger side only.

  1. Adjust the side television camera (LandCruiser RM000003XM401ZX.html).