Front Door Window Frame Moulding Removal


  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  4. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  5. REMOVE ASSIST GRIP COVER LH

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

  8. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

  10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

  11. REMOVE FRONT DOOR GLASS RUN LH

  12. REMOVE FRONT DOOR BELT MOULDING LH

  13. REMOVE FRONT DOOR WEATHERSTRIP LH

  14. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

Front Door Window Frame Moulding -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When removing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.
    Standard:
    Item
    		Temperature
    Vehicle Body
    		40 to 60°C (104 to 140°F)
    Window Frame Moulding
    		20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body or window frame moulding excessively.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 2 clips and remove the front door lower frame bracket garnish LH.



4. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.



5. REMOVE ASSIST GRIP COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using moulding remover A, detach the 8 claws and remove the assist grip cover.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 3 screws.

  1. Remove the 12 clips.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Removal

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    Text in Illustration
    *1
    		Reference Boss

  1. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the 2 connectors.



  1. w/ Seat Position Memory System:



      Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

    1. Disconnect the connectors.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.



7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.



8. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the bolt.

  1. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Detach the claw and remove the outer rear view mirror.



10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Removal

  1. Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


11. REMOVE FRONT DOOR GLASS RUN LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the front door glass run.



12. REMOVE FRONT DOOR BELT MOULDING LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Removal

  1. Put protective tape around the belt moulding.

  1. Detach the 6 claws and remove the front door belt moulding.

    Text in Illustration
    *1
    		Protective Tape


13. REMOVE FRONT DOOR WEATHERSTRIP LH


Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 3 clips and remove the upper part of the front door weatherstrip so that the moulding can be removed.



14. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the door window frame moulding clip.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Exterior Panels Trim.Front Bumper.Front Door Window Frame Moulding Removal

  1. Put protective tape around the front door rear window frame moulding.

  1. Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.

    Text in Illustration
    *1
    		Protective Tape
    *2
    		Double-sided Tape
    *3
    		Moulding Remover