Rear No. 2 Seat Assembly (For Power Seat Type Lh Side) -- Disassembly |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- NOTICE:
- Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (LandCruiser RM000001YWR010X.html).
- The fold seat control ECU is replaced with a new one.
- Initialization (initial position reset) of the fold seat control ECU is performed.
- Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (LandCruiser RM000001YWR010X.html).
- The fold seat control ECU is exchanged with one from another vehicle.
- The seatback frame and seat leg are inspected.
- The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
- The seatback frame or seat leg is replaced.
- The cable is disconnected from the battery while the seatback or seat cushion is operating.
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. REMOVE CAP |
Remove the 2 caps.
 |
| 2. REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH |
Remove the 2 screws.
 |
Detach the 3 claws and remove the cover.
| 3. REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH |
Remove the 2 screws.
Text in Illustration *1 Guide
 |
Detach the 2 claws and guide and remove the cover.
| 4. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
 |
Using a T45 "TORX" socket wrench, remove the bolt and inner belt assembly.
| 5. REMOVE FOLD SEAT CONTROL ECU |
Disconnect the 2 connectors.
 |
Remove the 2 nuts and ECU.
| 6. REMOVE REAR SEAT NO. 1 CUSHION MOULDING |
Using a clip remover, remove the 2 clips.
 |
Detach the 2 claws and 4 guides and remove the moulding.
Text in Illustration *1 Guide
| 7. REMOVE SEAT CUSHION COVER WITH PAD |
Open the 2 fasteners.
Text in Illustration *1 Fastener
 |
Remove the 2 clips and open the under part of the seat cushion cover.
 |
Detach the 2 hooks and remove the seat cushion cover with pad.
Text in Illustration *1 Hook
 |
| 8. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH |
Detach the fastener.
Text in Illustration *1 Fastener
 |
Remove the hog rings and seat cushion cover.
| 9. REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH |
Cut off the tack pins and remove the protector from the cushion pad.
Text in Illustration *1 Tack Pin
 |
| 10. REMOVE REAR SEAT NO. 2 CUSHION MOULDING |
Remove the 2 screws.
 |
Detach the 2 claws and remove the moulding.
| 11. REMOVE REAR SEAT NO. 3 LEG COVER LH |
Detach the 2 claws and remove the cover.
 |
| 12. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH |
Remove the screw and clip.
Text in Illustration *1 Guide
 |
Detach the guide and remove the cover.
| 13. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH |
Remove the screw and clip.
Text in Illustration *1 Guide
 |
Detach the guide and remove the cover.
| 14. REMOVE LOWER SEAT TRACK RAIL LH |
Remove the 2 bolts and seat track rail.
 |
| 15. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH |
Detach the 7 clips and remove the board.
 |
| 16. REMOVE REAR SEATBACK LOCK HOOK |
Remove the lock hook.
 |
| 17. REMOVE REAR SEAT NO. 1 COVER BEZEL |
Remove the 2 screws, detach the guide and remove the bezel.
Text in Illustration *1 Guide
 |
| 18. REMOVE SEATBACK COVER WITH PAD |
Detach the hooks.
Text in Illustration *1 Hook
 |
Detach the 8 clips and remove the seatback cover with pad.
 |
| 19. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH |
Remove the hog rings and seatback cover.
 |
| 20. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR |
Cut off the tack pins and remove the protector from the seatback pad.
Text in Illustration *1 Tack Pin
 |
| 21. REMOVE NO. 2 SEATBACK COVER |
Detach the 2 claws and remove the cover.
 |
| 22. REMOVE REAR SEAT HEADREST COVER |
Remove the 2 screws.
Text in Illustration *1 Guide
 |
Detach the 2 claws and guide and remove the cover.
| 23. REMOVE REAR SEAT HEADREST CABLE |
Detach the 2 clamps.
Text in Illustration *1 Cable End *2 Clamp
 |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
| 24. REMOVE REAR SEAT HEADREST ASSEMBLY |
Remove the 3 nuts and headrest.
 |
| 25. REMOVE REAR SEATBACK EDGE PROTECTOR |
Detach the 4 claws and remove the 2 protectors.
 |
| 26. REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH |
Detach the 4 claws and remove the cover.
 |
| 27. REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH |
Remove the screw.
Text in Illustration *1 Guide
 |
Detach the guide and 2 claws and remove the cover.
| 28. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH |
Remove the bolt and disconnect the wire harness.
 |
Using a screwdriver, release the lock lever as shown in the illustration.
 |
Retract the seat cushion frame.
 |
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.
| 29. REMOVE REAR SEAT LEG COVER LH |
Remove the clip.
Text in Illustration *1 Hook
 |
Detach the 3 hooks and 5 clips and remove the cover.
| 30. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH |
Remove the 3 clips.
Text in Illustration *1 Guide
 |
Detach the 2 claws and 4 guides and remove the 3rd seat link.
| 31. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH |
Detach the 5 claws and remove the cover.
 |
| 32. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH |
Remove the screw.
Text in Illustration *1 Guide
 |
Detach the guide and 2 claws and remove the cover.
| 33. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH |
Detach the 2 clamps.
Text in Illustration *1 Clamp *2 Cable End
 |
Twist the cable end in the direction indicated by the arrow and remove the cable.
| 34. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side) |
Cut off the 2 cable ties and detach the 3 clamps.
Text in Illustration *1 Cable Tie *2 Clamp *3 Cable End
 |
Twist the cable end in the direction indicated by the arrow and remove the cable.
| 35. REMOVE REAR SEAT LOCK CONTROL CABLE LH |
Detach the 2 clamps.
Text in Illustration *1 Cable End *2 Clamp
 |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
| 36. REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side) |
Cut off the 2 cable ties and detach the 3 clamps.
Text in Illustration *1 Cable Tie *2 Clamp *3 Cable End
 |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
| 37. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.
 |
| 38. REMOVE REAR NO. 2 SEAT WIRE LH |
Disconnect the connector.
 |
Detach the wire harness clamps and remove the seat wire.
| 39. REMOVE NO. 3 SEAT LEG ASSEMBLY LH |
Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.
 |
| 40. REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side) |
Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.
 |