REMOVE REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)
REMOVE REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)
Rear No. 2 Seat Assembly (For Power Seat Type Lh Side) -- Removal |
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- NOTICE:
- Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (LandCruiser RM000001YWR010X.html).
- The fold seat control ECU is replaced with a new one.
- Initialization (initial position reset) of the fold seat control ECU is performed.
- Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (LandCruiser RM000001YWR010X.html).
- The fold seat control ECU is exchanged with one from another vehicle.
- The seatback frame and seat leg are inspected.
- The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
- The seatback frame or seat leg is replaced.
- The cable is disconnected from the battery while the seatback or seat cushion is operating.
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. REMOVE DECK BOARD ASSEMBLY |
Operate the No. 2 fold seat switch and fold down the 2 seatbacks.
Remove the 2 bolts.
 |
Detach the 4 clips and remove the deck board.
| 2. REMOVE REAR NO. 4 FLOOR BOARD |
Using a moulding remover, detach the clip and 3 claws.
Text in Illustration *1 Guide
 |
Detach the 2 guides and remove the floor board.
| 3. REMOVE REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System) |
Using a moulding remover, detach the clip and 4 claws.
Text in Illustration *1 Guide
 |
Detach the 2 guides and remove the floor board.
| 4. REMOVE REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System) |
Using a moulding remover, detach the clip and 3 claws.
Text in Illustration *1 Guide
 |
Detach the 2 guides and remove the floor board.
| 5. REMOVE REAR FLOOR MAT SUPPORT PLATE |
Remove the 3 bolts.
Text in Illustration *1 Guide - -
Detach the 4 claws and 2 guides.
Detach the 5 clips and remove the support plate.
| 6. REMOVE DECK BOARD BRACKET REINFORCEMENT |
Remove the 2 bolts.
Text in Illustration *1 Hook
 |
Detach the 2 hooks and reinforcement.
| 7. REMOVE NO. 1 DECK BOARD BRACKET LH |
Remove the 2 bolts and bracket.
 |
| 8. REMOVE REAR NO. 2 SEAT ASSEMBLY LH |
Operate the No. 2 fold seat switch and raise the 2 seatbacks.
Disconnect the connector.
 |
Remove the 2 bolts.
 |
Using a screwdriver, detach the 2 guides and 6 claws and open the 2 covers.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective Tape *2 Guide
 |
Remove the 2 bolts.
 |
Remove the rear No. 2 seat assembly from the vehicle.
- NOTICE:
- Be careful not to damage the vehicle body.
- HINT:
- If removing the seat on the RH side with the LH side installed, remove it with the No. 3 rear seat leg cover LH raised as shown in the illustration.
 |