INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)
Rear Airbag Sensor (For 5 Door) -- Installation |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. INSTALL REAR AIRBAG SENSOR LH |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Install the rear airbag sensor with the nut.
- Torque:
- 9.0 N*m{92 kgf*cm, 80 in.*lbf}
- NOTICE:
- If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
- When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
Check that the rear airbag sensor is not loose.
Connect the connector.
| 2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
w/o Rear No. 2 Seat:
Pass the rear seatback lock control lever base through the deck trim side panel.
Attach the 5 clips and 8 claws to install the deck trim side panel.
Install the 4 bolts and 2 screws.
Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
w/ Rear No. 2 Seat:
Attach the 4 clips and 8 claws to install the deck trim side panel.
Install the 2 bolts and 2 screws.
Install the rear No. 2 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Install the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
| 3. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure for the other assist grip.
Install the assist grip with the 2 bolts.
| 4. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure for all assist grip plugs.
Attach the 2 claws to install the assist grip plug.
| 5. INSTALL FRONT DECK SIDE TRIM COVER |
- HINT:
- Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover
| 6. INSTALL NO. 1 TONNEAU COVER HOLDER CAP |
- HINT:
- Use the same procedure for the other No. 1 tonneau cover holder cap.
Attach the 2 claws to install the No. 1 tonneau cover holder cap.
| 7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
- HINT:
- Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook by turning it clockwise.
| 8. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER |
- HINT:
- Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.
| 9. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat) |
Attach the 4 claws to install the rear floor carpet.
Text in Illustration *A w/o Deck Rail *B w/ Deck Rail *C for Face to Face Seat Type - -
| 10. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail) |
Install the floor side rail with the 3 bolts.
| 11. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail) |
- HINT:
- Use the same procedure described for the LH side.
| 12. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat) |
Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.
| 13. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat) |
Attach the clip to install the No. 1 deck board.
| 14. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat) |
 |
- HINT:
- Use the same procedure for the other front luggage compartment trim cover.
Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.
Text in Illustration *1 Luggage Hold Belt Striker
Attach the 4 claws to install the cap.
| 15. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover.
| 16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
 |
Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.
Text in Illustration *1 Paint Mark *2 Mark Position
| 17. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate.
| 18. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat) |
Install the quarter scuff plate with the 2 bolts.
| 19. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedure for all rear No. 1 floor step covers.
Attach the 2 claws to install the rear No. 1 floor step cover.
| 20. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
for Manual Seat Type LH Side:
Install the rear No. 2 seat assembly (LandCruiser RM0000045D9008X.html).
for Power Seat Type LH Side:
Install the rear No. 2 seat assembly (LandCruiser RM0000045DE00EX.html).
for Face to Face Seat Type:
Install the rear No. 2 seat assembly (LandCruiser RM0000045DV006X.html).
| 21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- CAUTION:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).
| 22. CHECK SRS WARNING LIGHT |
Check the SRS warning light (LandCruiser RM000000XFD0N3X.html).